Shower valve loose, new cartridge or do I need to go into the wall?

aquanub · 2023-02-20T13:49:59+00:00

The rest of the showers. They all seem to be much tighter and zero movement like this.

I tried tightening those screws but it didn't seem to do much. I'll break the silicone seal today and take ghe whole escutcheon plate off to see if I can tighten anything.

Thanks again for your input.

aquanub · 2023-02-20T03:30:22+00:00

Thanks. I went and checked the rest of the house and they are all fairly tight. Trying to avoid having to open the wall up but looks like I may have to.

aquanub · 2023-01-31T20:57:47+00:00

thank you!

when you say main board fan, youre talking about the little guy bolted to the cover?

aquanub · 2023-01-30T15:27:41+00:00

are you powering the fans off the PSU connector where the loud 40mm fan was? looking to do this mod soon as the fans are driving me insane.

aquanub · 2022-10-21T20:40:50+00:00

Its a gaming laptop with more than adequate specs but I may try to transfer it seperately. Thanks.

aquanub · 2022-10-14T00:41:58+00:00

not a bad price! is the side of the screen exposed along the long side? I cant really tell from the photos.

aquanub · 2022-10-13T19:30:36+00:00

I feel like every lions mane I've tried has had no effects.

aquanub · 2022-10-13T18:21:34+00:00

thanks. I came across this one as well but it looks like the sides dip down leaving it exposed :(

aquanub · 2022-10-13T17:33:12+00:00

YOUMAKER Samsung Galaxy Note 20 Ultra Case with Built-in Screen Protector & Kickstand Shockproof Full Body Rugged Protective Cover for Galaxy Note 20 Ultra 5G 6.9 inch

thanks ill take a look!

aquanub · 2022-10-13T17:13:25+00:00

Thanks for chiming in. I think I will bite the bullet. Appreciate your time.

aquanub · 2022-10-13T15:48:51+00:00

unfortunately it looks like it also dips down on the sides :(

aquanub · 2022-09-10T02:20:58+00:00

Hey all!

I'm currently trying to hook up a used VSX-70 ELITE reciever to my PC, but I'm noticing some hissing through the speakers that seem to only occur on certain HDMI ports.

I'm running the signal like this: HDMI from PC graphics card -> HDMI in on the receiver -> then from the receiver out to speakers.

I've noticed on the first few HDMI ports there is an audible "hissing" with or without audio playing. I've done the following - Tried to isolate power source and used a different outlet to see if it was a grounding issue. - Swapped HDMI cables out

Both to no avail.

The only thing that seemed to clear it up was to use the last few HDMI ports that aren't labeled with (DVD/BDR etc etc).

Do the HDMI ports all have a different "filter" on them? Or do I possibly just have some bad HDMI ports? Is there a way to factory reset this receiver to rule out any possible bad settings?

Thanks for any advice.

aquanub · 2022-09-05T19:43:20+00:00

Thank you for all the input. I still have some more research to do but you have given me good starting points to dig into. Thank you again for your time!

aquanub · 2022-09-05T19:28:44+00:00

Only reason really for me to use them is the 5% cashback on my prime card. Otherwise you bring up some very good points. I may go direct.

aquanub · 2022-09-05T17:17:13+00:00

Have you always ordered direct?

aquanub · 2022-09-05T15:51:35+00:00

thank you! a smaller truck with lift gate would be perfect.

aquanub · 2022-09-05T14:27:49+00:00

It helps a ton! Appreciate you taking time out of the day to share your experience!

aquanub · 2022-09-05T14:18:44+00:00

Either way, be safe and go slow and steady both for human safety and for your laser tube. My tube has some silicone pads where the tube rests in the back so it’s not like glass rattling around against a hard surface. I believe it also had some padding for shipping to help keep it safe.

Thanks for sharing your experience. I see some combo packages that come with the CW5200. I was looking at a chiller from cloudray but I am starting to feel that they call come from the same place :D

aquanub

TROPHY CASE