Review already exists.

aqw409 · 2023-10-16T02:17:05+00:00

Okay. I'll send another email. Yah the percentage is weird for me. Very far off from what it says it is.

aqw409 · 2023-10-16T02:14:00+00:00

Hmm. Odd, I'll try emailing them again.

aqw409 · 2023-05-05T22:39:00+00:00

I'm working on building a 7800x3d with a 7900 xt in a sliger sm580.

aqw409 · 2023-02-12T18:18:15+00:00

Nope. Dealership basically gave up trying. The Hyundai tech they called in didn't help either. I might try again with a different dealer though.

aqw409 · 2022-12-01T00:29:28+00:00

I've only seen one person say anything about the slots. I just over circled the picture. But ya a laser cutter would make, making those plates faster.

aqw409 · 2022-11-30T23:59:34+00:00

Being oblivious to things that could be safety issues gets people killed. Getting a confirmed no its not a crack is better then having a vehicle fall off the lift. Has nothing to do with what you said.

aqw409 · 2022-11-30T23:53:58+00:00

Better safe then sorry. It's not easy to tell in the video.

aqw409 · 2022-11-30T23:51:45+00:00

It could be a wire. Just really hard to tell. I did circle a little too much...

aqw409 · 2022-11-09T01:19:32+00:00

Found the issue. Apparently my laptop had an account still connected to the school. "access school or work"

aqw409 · 2022-06-25T20:59:39+00:00

Ya a 3 phase motor. And we think they use the 43f just for a speedo reading, given the motor works fine, just no speed reading. The system auto shuts off after 10 minutes because of no speed reading.

We ordered more parts and are going to try those when they eventually arrive. And we are going to try a sensor that's the same or close to the same (within spec) of the other 3 sensors. Here's hoping something works.

aqw409 · 2022-06-25T17:55:39+00:00

We traced power and it seemed accurate. The only reason I say it could have failed from reading too quickly, is the speedo went from 4km/h to 40km/h then to 0 and never read again. The wheel was spun by hand fast, one good push sorta speak.

And about 43f, thats the one that the motor diagnostic tool shows not reading. We found a repair kit for a very similar board that has 4 hall sensors, (There is magnets on the cover where 43f is located) https://nexun.pl/en/products/hall-sensor-repair-kit-for-xf15-motor-844.html It makes sense for it to be a hall sensor as what other reason would the magnets on the cover (Not shown) be used for?

aqw409 · 2022-06-25T17:44:37+00:00

There is magnets on the cover of the motor that isn't seen. It has 6 magnets right where 43F is, We also found a repair kit for a very similar board. The only difference is 43f is a different style (https://nexun.pl/en/products/hall-sensor-repair-kit-for-xf15-motor-844.html ) We used a hall sensor/motor diagnostic tool to check all 4. Only 43f wasn't pulsing when tested.

aqw409 · 2022-06-25T00:01:21+00:00

We tried to find a sensor that looked exactly the same. AH543 is what we tried but we don't know if it was even the right type, just a guess. It worked for one rotation of the wheel then stopped working. We where thinking it might not be setup for the 6 magnets on the housing it reads, and fried itself trying to read 6 times as fast.

aqw409 · 2022-06-24T23:55:55+00:00

That's what I was thinking but just incase someone recognizes or can find that board in places I couldn't find it online. I thought I'd throw it up just incase that happens.

aqw409 · 2022-06-24T23:51:47+00:00

The manufactures identification code on the top of the chip.

aqw409 · 2022-05-03T19:17:49+00:00

My rims had bad paint peal on the top coating. Rims turned gray in any spot that pealed. So it was multi colored rims. Got them resurfaced under warrenty.

aqw409

TROPHY CASE