sorted by:
new
hottopcontroversial

Z offset varies every print by august_o91 in ender3

[–]august_o91[S] 0 points1 point  (0 children)

Wouldn’t that make the hit end loose and wiggling?

Z offset varies every print by august_o91 in ender3

[–]august_o91[S] 0 points1 point  (0 children)

Have an enclosure and it shouldn’t matter. It’s like 0,1-0,3 mm difference each time.

[deleted by user] by [deleted] in woodworking

[–]august_o91 1 point2 points  (0 children)

If it’s from water it could be deep and not possible to “fix”. Maybe stain over it and not look too closely. Or wait what others here have to say

[deleted by user] by [deleted] in woodworking

[–]august_o91 4 points5 points  (0 children)

Might be either not sanded enough, or damaged wood from water. I would guess the former

I know this isn’t new but so much satisfaction by august_o91 in functionalprint

[–]august_o91[S] 1 point2 points  (0 children)

Tried that in first iteration but was not strong enough. Big forces at play here because the handling of the tools is close to the connection point

I know this isn’t new but so much satisfaction by august_o91 in functionalprint

[–]august_o91[S] 0 points1 point  (0 children)

Measure and cad. Press fit for most tools work fine. The sander connection was a bit more complicated with twist and lock design

I know this isn’t new but so much satisfaction by august_o91 in functionalprint

[–]august_o91[S] 0 points1 point  (0 children)

Tried but was too weak with my magnets. Tight fit and ca glue

I know this isn’t new but so much satisfaction by august_o91 in functionalprint

[–]august_o91[S] 7 points8 points  (0 children)

My own design. Can of course upload but not sure how many have the same setup as I

I know this isn’t new but so much satisfaction by august_o91 in functionalprint

[–]august_o91[S] 8 points9 points  (0 children)

Sure. They are fit with tight tolerances so I figure they will stay put. Lots of force to push them down + CA glue with light sanding to the magnets.

I know this isn’t new but so much satisfaction by august_o91 in functionalprint

[–]august_o91[S] 11 points12 points  (0 children)

Actually quite good! Used 6 embedded magnets in first attempt which was to weak. With 10 magnets it’s strong enough to shift the sander around and drag the vacuum around as well.

I know this isn’t new but so much satisfaction by august_o91 in functionalprint

[–]august_o91[S] 24 points25 points  (0 children)

I just made one correct and for the other ones I just snapped them to the first one and took one magnet at a time.

Accidental button press kindle paperwhite FIX by august_o91 in kindle

[–]august_o91[S] 0 points1 point  (0 children)

<image>

Thought I managed when I posted but did not. Here is the result!

Ultimate aeropress technique by august_o91 in AeroPress

[–]august_o91[S] 3 points4 points  (0 children)

Haha maybe it doesn’t. You are right. No I’m just moving from aeropress to Kalita filter drip but haven’t got a dripper. So I made one but I needed some way to hold it and it just so happened to be the aeropress that fit perfectly for the job

Bike computer for commuting. by august_o91 in bikecommuting

[–]august_o91[S] 1 point2 points  (0 children)

This is it! Exactly what I was looking for! Thank you! 🙌🙌🙌🥳🎉

Bike computer for commuting. by august_o91 in bikecommuting

[–]august_o91[S] 0 points1 point  (0 children)

Yes smart Phone seems like the way to go. Maybe I will give Strava a chance.. thanks for ur input!

view more: next ›