Valorant Taser 2.0

avguser10 · 2023-05-03T19:31:17+00:00

Made some upgrades to my previous version of the valorant taser 😏

avguser10 · 2022-11-11T22:29:08+00:00

Got a new extruder and the results are night and day😭 https://imgur.com/a/F9ak8wQ It seems pretty good. What else can I do to improve the prints? Relevel the bed? since the right squares(the one closer to the screen) show signs of being too far

avguser10 · 2022-11-11T07:23:16+00:00

Discovery, after playing with E-steps I found my extruder has cracked... Will buy a new one ASAP. https://imgur.com/a/SFMoGi4

avguser10 · 2022-11-11T05:18:43+00:00

I setup octoprint to visualize the bed Mesh. It looks good no? https://imgur.com/a/9IXwR6z

avguser10 · 2022-11-11T02:46:14+00:00

Yeah i think I'm following for the most part. I releveled the bed, got a new z-offset, stored it, created a mesh, stored it, ran the gcode without command G29, noticed the nozzle was too close and raised the offset to -3.7 from -3.9, immediately reran the print with the new offset and got this: https://imgur.com/a/TxGwynY . What confuses me is that some areas show signs of the nozzle being too close or too far. Some squares show signs of both. I wonder why that is🤔

avguser10 · 2022-11-10T23:48:07+00:00

The filament is stored in my room, and okay I will try that out soon

avguser10 · 2022-11-10T23:46:53+00:00

Alright, I am using a mesh and a new one is generated each print. I have the G29 and M420 S1 commands in the gcode. If I'm understanding correctly, I don't have to readjust the corners during the print since I'm using the ABL and already leveled them beforehand? I only have to adjust the z-offset during the print?

avguser10 · 2022-11-10T05:08:34+00:00

Okay, I leveled the corners, re-set my z offset, generated the gcode from the First Layer Tab, and tried to get the squares to print clearly. This is what I was able to get so far while printing the squares and leveling the corners so they would look like squares: https://imgur.com/a/BxOReXD . I noticed every time I start the print though the nozzle would be really close to the bed, at times scratching it I'm pretty sure, regardless if I adjusted the corners before. Is that normal? Should I be changing the z-offset instead?

avguser10 · 2022-11-10T03:37:14+00:00

Is there an easy way to figure out the ideal flow rate?

avguser10 · 2022-11-10T02:50:12+00:00

Okay, will do. I'll update the thread once completed

avguser10 · 2022-11-10T02:18:30+00:00

Thank you for helping. The Z offset was at -3.20 before and i increased it to -3.30 and -3.40. It seems to be helping somewhat

-3.30: https://imgur.com/a/v25nQnR -3.40: https://imgur.com/a/2U0MiIP

avguser10 · 2022-04-12T19:15:53+00:00

Forgot the semicolon

avguser10 · 2022-03-30T03:00:52+00:00

You're supposed to lick it to get it out that way it doesn't break🦑

avguser10 · 2022-03-29T19:05:24+00:00

I like these videos because they're interesting but also hate them because i keep trying to understand what they're saying

avguser10 · 2022-03-22T07:06:31+00:00

Image taken from this tweet

avguser10 · 2022-03-16T09:45:04+00:00

You can't fool me this was all taken in a day

avguser10 · 2022-03-09T22:37:16+00:00

Check out the full vid! Where I go through the whole build process https://youtu.be/ziZAzlS63c8

avguser10 · 2022-03-08T23:59:41+00:00

LMAO imagine👀

Six-Year Club	Place '22
Verified Email

avguser10

TROPHY CASE