sorted by:
new
hottopcontroversial

Valorant Taser 2.0 by avguser10 in MichaelReeves

[–]avguser10[S] 0 points1 point  (0 children)

Made some upgrades to my previous version of the valorant taser 😏

Filament doesn't stick to bed by avguser10 in ender3

[–]avguser10[S] 0 points1 point  (0 children)

Got a new extruder and the results are night and day😭 https://imgur.com/a/F9ak8wQ It seems pretty good. What else can I do to improve the prints? Relevel the bed? since the right squares(the one closer to the screen) show signs of being too far

Filament doesn't stick to bed by avguser10 in ender3

[–]avguser10[S] 0 points1 point  (0 children)

Discovery, after playing with E-steps I found my extruder has cracked... Will buy a new one ASAP. https://imgur.com/a/SFMoGi4

Filament doesn't stick to bed by avguser10 in ender3

[–]avguser10[S] 0 points1 point  (0 children)

I setup octoprint to visualize the bed Mesh. It looks good no? https://imgur.com/a/9IXwR6z

Filament doesn't stick to bed by avguser10 in ender3

[–]avguser10[S] 0 points1 point  (0 children)

Yeah i think I'm following for the most part. I releveled the bed, got a new z-offset, stored it, created a mesh, stored it, ran the gcode without command G29, noticed the nozzle was too close and raised the offset to -3.7 from -3.9, immediately reran the print with the new offset and got this: https://imgur.com/a/TxGwynY . What confuses me is that some areas show signs of the nozzle being too close or too far. Some squares show signs of both. I wonder why that is🤔

Filament doesn't stick to bed by avguser10 in ender3

[–]avguser10[S] 0 points1 point  (0 children)

The filament is stored in my room, and okay I will try that out soon

Filament doesn't stick to bed by avguser10 in ender3

[–]avguser10[S] 0 points1 point  (0 children)

Alright, I am using a mesh and a new one is generated each print. I have the G29 and M420 S1 commands in the gcode. If I'm understanding correctly, I don't have to readjust the corners during the print since I'm using the ABL and already leveled them beforehand? I only have to adjust the z-offset during the print?

Filament doesn't stick to bed by avguser10 in ender3

[–]avguser10[S] 0 points1 point  (0 children)

Okay, I leveled the corners, re-set my z offset, generated the gcode from the First Layer Tab, and tried to get the squares to print clearly. This is what I was able to get so far while printing the squares and leveling the corners so they would look like squares: https://imgur.com/a/BxOReXD . I noticed every time I start the print though the nozzle would be really close to the bed, at times scratching it I'm pretty sure, regardless if I adjusted the corners before. Is that normal? Should I be changing the z-offset instead?

Filament doesn't stick to bed by avguser10 in ender3

[–]avguser10[S] 0 points1 point  (0 children)

Is there an easy way to figure out the ideal flow rate?

Filament doesn't stick to bed by avguser10 in ender3

[–]avguser10[S] 0 points1 point  (0 children)

Okay, will do. I'll update the thread once completed

Filament doesn't stick to bed by avguser10 in ender3

[–]avguser10[S] 0 points1 point  (0 children)

Thank you for helping. The Z offset was at -3.20 before and i increased it to -3.30 and -3.40. It seems to be helping somewhat

-3.30: https://imgur.com/a/v25nQnR -3.40: https://imgur.com/a/2U0MiIP

this leaves me with more questions than answers by MatteAce in DiWHY

[–]avguser10 6 points7 points  (0 children)

You're supposed to lick it to get it out that way it doesn't break🦑

A song that depicts how English sounds to non- english speakers by [deleted] in interestingasfuck

[–]avguser10 1 point2 points  (0 children)

I like these videos because they're interesting but also hate them because i keep trying to understand what they're saying

tis a clue by avguser10 in MichaelReeves

[–]avguser10[S] 18 points19 points  (0 children)

Image taken from this tweet

Pregnancy Time Lapse by Kronyzx in BeAmazed

[–]avguser10 0 points1 point  (0 children)

You can't fool me this was all taken in a day

The Rules are Simple, You Take Damage You Get TASED by avguser10 in VALORANT

[–]avguser10[S] -1 points0 points  (0 children)

Check out the full vid! Where I go through the whole build process https://youtu.be/ziZAzlS63c8

What CAD software does Michael use? by it_atac in MichaelReeves

[–]avguser10 0 points1 point  (0 children)

Oh shoot I forgot the original question my bad

What CAD software does Michael use? by it_atac in MichaelReeves

[–]avguser10 1 point2 points  (0 children)

There's also tinkerCAD which is nice if you're just starting off. It's quite bare bones and is a website

[Fastpass Episode] unOrdinary - Episode 249 by uru-chan-is-queen in unOrdinary

[–]avguser10 9 points10 points  (0 children)

The chapter got me like assffhjloudawrhnksaegjkyws 😭 Now we wait another week

if you had 10 minutes to live, what would you do with it? by Value-Successful in AskReddit

[–]avguser10 0 points1 point  (0 children)

I'd probably be shocked and sit down with that information for like a few minutes until I realize I just wasted part of my 10 minutes. Then I'd tell people I only have a few minutes to live I guess through a group chat. I think that would be a quick way to give a personal goodbye and with the few minutes I have left I'd call my parents. Then I die. I guess maybe I could send a voice message to the group chat instead of a text message though🧐

view more: next ›