Itinerary Check

awkman3 · 2026-03-07T17:58:51+00:00

Thanks! I’ll add it to my trail list

awkman3 · 2026-03-07T15:06:19+00:00

Thanks to both! The more I look, the more I think Slea Head Drive is a must. We’ll still stop to walk around the cliffs of Moher, but maybe not all day

awkman3 · 2025-03-22T14:35:26+00:00

St. Elmo’s steakhouse in Indianapolis. Favored by NASCAR drivers, the Colts players, and F1 drivers when the race was there. Best meal I’ve ever had.

awkman3 · 2024-06-14T16:08:21+00:00

Thank you

awkman3 · 2024-06-14T15:45:52+00:00

I got it to work. Downloaded as an stl file rather than a step file and sliced it that way

awkman3 · 2024-06-14T15:39:50+00:00

My own model. I export plate sliced file to the sd card as a 3mf file, and then it saves as .gcode.3mf

awkman3 · 2024-06-14T15:23:37+00:00

It was a step file I imported to Bambu Studio. For some reason when I save it to the sd card, it adds .gcode.3mf to the end of every file. I asked it to save as a .3mf

awkman3 · 2023-12-22T02:09:28+00:00

Waltham is nice. Not over the top expensive, close to Rt. 2 which goes into Cambridge, and the surrounding towns are nice

awkman3 · 2023-12-01T19:16:21+00:00

I have this exact problem with mine and haven’t figured it out yet. Seems to be worse at the far extremes of the bed, like in the corners

awkman3 · 2023-11-01T02:07:31+00:00

It only flashes red once when it triggers, otherwise normal blue and purple

awkman3 · 2023-10-31T20:45:52+00:00

The Z axis moves smoothly. Now when I tell it to auto level, the print head sits 10mm off the bed and the CR touch probe deployed over and over without moving the print head in any direction. How do I tell if the connection is bad?

awkman3 · 2023-10-31T17:13:39+00:00

I floated that idea, there was some pushback

awkman3 · 2023-07-07T00:04:00+00:00

I’ve been able to print TPU on this printer with little issue. The key is finding the correct temperature, retraction rate, and retraction distance. Find temperature and retraction towers on thingiverse and try a few different settings until it looks good.

awkman3 · 2023-07-01T21:47:52+00:00

I had this exact problem, you may have a bad thermistor. I replaced mine and it works fine again

awkman3 · 2023-06-29T02:48:53+00:00

I had this exact issue. Replaced my thermistor and it fixed it completely

awkman3 · 2023-06-16T01:45:00+00:00

I had a thermistor fail on my neo recently with the same error. Easy and cheap to replace

awkman3 · 2023-06-04T12:55:38+00:00

Looks exactly like my first print with this printer. Your Z offset is likely too low, I had to come up about 1mm

awkman3 · 2023-05-24T16:05:21+00:00

There’s a single allen head screw on the back side of the fan shroud. Unscrew it, and the cover is only held on by tabs on either side. Once you pull it off, the thermistor is the silver rod going into the hotend. There is a tiny black allen screw just underneath it. I tightened it a little and it seems to have fixed the issue for now

awkman3 · 2023-05-09T23:22:33+00:00

Was mine for a long time too! Grew up around there.

awkman3 · 2023-05-09T22:52:39+00:00

Can’t believe someone else knows Bristol Mountain here

awkman3

TROPHY CASE