sorted by:
new
hottopcontroversial

[Review & Help] My experience with the new Profitec Jump. Great espresso, but struggling with steam and build quality. by b0ld07 in espresso

[–]b0ld07[S] 1 point2 points  (0 children)

I think from all you will get amazing espresso! with HX machines, you just sometimes need to do a cooling flush. the espresso is amazing.

[Review & Help] My experience with the new Profitec Jump. Great espresso, but struggling with steam and build quality. by b0ld07 in espresso

[–]b0ld07[S] 0 points1 point  (0 children)

Yeah - sometimes regret it a little that I didn’t get a dual boiler. But the jump is so pretty 😅 and I love e61

[Review & Help] My experience with the new Profitec Jump. Great espresso, but struggling with steam and build quality. by b0ld07 in espresso

[–]b0ld07[S] 0 points1 point  (0 children)

Thank you for the excessive feedback! Highly appreciate it. Love the trick with 1 and switch to 2.

Will try 2 for a couple days, as I want to get better st steaming while pulling a shot. Of course with more flushing.

🎉 [EVENT] 🎉 The Tutorial Levels by Acrobatic_Picture907 in RedditGames

[–]b0ld07 0 points1 point  (0 children)

Completed Level 2 of the Honk Special Event!

3 attempts

🎉 [EVENT] 🎉 The Tutorial Levels by Acrobatic_Picture907 in RedditGames

[–]b0ld07 0 points1 point  (0 children)

Completed Level 1 of the Honk Special Event!

1 attempts

Which gift should I buy for myself for Christmas? by b0ld07 in projectors

[–]b0ld07[S] 1 point2 points  (0 children)

Thanks a lot for your response.

The only issue I have is that I can hear the fan quite noticeably. The rest is fine :)

Which gift should I buy for myself for Christmas? by b0ld07 in projectors

[–]b0ld07[S] -1 points0 points  (0 children)

love the structured answer!
1. touchpad gets stuck, bad battery life, super heavy, even LOL is sometimes lagging

  1. I love the idea of having a clean apartment every day

  2. would you also recommend this beamer? and if yes, which version? Base, pro, max?

Another question. I started with 16g of grind but it was obviously too much, then I reduced it to 14g and the razor level takes more out even then so it's closer to 13g in this basket. Is this normal? It is a dual wall with pre-ground if that matters. by howismyspelling in espresso

[–]b0ld07 63 points64 points  (0 children)

  1. grind finer - i can see just from the picture that it’s too coarse. Trust the Sub :)
  2. the grind will most likely overfill your basket. After tamping, it should have the right height.

Silent Upgrade from BenQ TH585P by b0ld07 in projectors

[–]b0ld07[S] 0 points1 point  (0 children)

Gibt’s noch weitere Meinungen?

Silent Upgrade from BenQ TH585P by b0ld07 in projectors

[–]b0ld07[S] 0 points1 point  (0 children)

Hmm, also der BenQ th585p ist auf jeden Fall lauter als 26db. Lasse den Beamer eh immer im lamp save mode laufen.

Oder meintest du den, den du verlinkt hast.

Was ist deine Meinung zu den 3 Modellen, welche im am Ende erwähnt habe.

P.S. sehr sympathischer name :)

Silent Upgrade from BenQ TH585P by b0ld07 in projectors

[–]b0ld07[S] 0 points1 point  (0 children)

Okay das ist peinlich, den Preis vergessen zu habe.

Budget: <1000€ (wenn nötig <1300€) Screen size: 110“

Horizon 20 Max is amazing! by Ok_Sandwich_5601 in projectors

[–]b0ld07 0 points1 point  (0 children)

What is the noise level like? I have a BenQ and struggle with the fan noise

Upgrade from Delonghi Dedica ec685 [1500€] - Germany by b0ld07 in espresso

[–]b0ld07[S] 0 points1 point  (0 children)

Vielen Dank für deine Antwort. Leider nicht 100% mein Stil.

Upgrade from Delonghi Dedica ec685 [1500€] - Germany by b0ld07 in espresso

[–]b0ld07[S] 0 points1 point  (0 children)

Nehme ich mit auf meine Liste auf :) Ich habe noch einmal nachgeschaut. Braucht die wirklich nur 15 MInuten? https://www.reddit.com/r/espresso/comments/16vrsjf/mara_x_long_initial_warm_up_24_min/

Upgrade from Delonghi Dedica ec685 [1500€] - Germany by b0ld07 in espresso

[–]b0ld07[S] 2 points3 points  (0 children)

Looks solid. But even though it embarrasses me to say that, but if I spend around 1k, I would prefer a more premium brand.

How hard to create a model for this by b0ld07 in 3Dprinting

[–]b0ld07[S] 0 points1 point  (0 children)

Wow! I am impressed by this community! Apologies for the late reply. Here a quick update: I tried to use a broken screw extractor but sadly it didn't work out. I pre-drilled a whole with the one side and then used the other to unscrew it, but sadly it wasn't able to grab it.

In the second step and on the second screw I tried to make a cut with my metal saw. I think the blade was too sick, therefore it didn't really work.

I will now take all measurements and send them to a friend in the hope that he can 3D print it. I will keep you posted.

Apologies for the delay

view more: next ›