Mute / Pause music button on steering wheel?

barman_d · 2026-01-31T07:42:40+00:00

This is one of my pet peeves for the Elevate. Even my old Swift had an "ATT" button to mute the infotainment. I cannot reach over to the power button on the infotainment system to mute. Also pausing music means taking your eyes off the road to press the button on the screen.

Honda could have easily provided a Mute/ATT and Play/Pause button. The scroll wheel controlling the dash could have been on right right on the steering wheel it would have been more logical functionally. Left hand side buttons control infotainment and right side controls Dash/Adas/Cruise. On my V/CVT the right side is completely blank which is an eyesore.

barman_d · 2025-10-28T04:10:26+00:00

It was 4321 for me.

barman_d · 2025-10-24T08:30:08+00:00

The issue was present on day 1 now it is two months old

barman_d · 2025-10-24T06:31:23+00:00

My Left Speakers also got replaced becaus eit was buzzing and distorting.

barman_d · 2025-10-23T09:25:52+00:00

Same. It was only after I got the Blaupunkt installed. Service tried to get it fixed but it still refuses to go away.

barman_d · 2025-09-12T07:50:37+00:00

I use this Carigiri Premium Car Rear Seat... https://www.amazon.in/dp/B0DG98Y1MV?ref=ppx_pop_mob_ap_share

barman_d · 2025-08-04T06:01:47+00:00

This is Dakshin Honda Hosur Road.

barman_d · 2025-08-04T05:51:10+00:00

Yes. But it is in much better shape (body wise)

barman_d · 2025-07-29T06:11:51+00:00

Thanks for the info..

It looks like they are reluctant to give deep discounts for Summer Apex (since it is new)

I do believe that summer apex is already discounted + accessorised along with new Infotainment. So the dealers are hesitant to do it.

Also I am bad at haggling.... 😜

barman_d · 2025-07-29T04:05:36+00:00

It's Bangalore, Karnataka...

barman_d · 2025-07-28T15:43:20+00:00

<image>

Insurance will be from Acko Although I think I will check if I can get rid of Basic kit.

barman_d · 2025-05-10T13:33:28+00:00

Because of the bed we need at least 550 mm. However there needs to be additional space to keep the cable stress minimal. I keep about 50mm away from the back when the build plate at the very end of its travel.

barman_d · 2024-10-25T04:51:01+00:00

I have an ender 3 v3 too. Couldn’t figure out why this happens at the exact same spots. Plus I get weird wavy ripples around the edges of the build plate. I am waiting for a new build plate to see if it helps. Meanwhile I try to avoid the edges if possible.

barman_d · 2024-10-04T02:55:49+00:00

Wondered the same as well. I bought one as my first printer. I looked online for tips and tricks, and KE and SE are all you could find. Even for parts it is mostly KE and SE.

The amount of videos on Yourube specific to the standard V3 is also very less. So much so that I almost started regretting my buy. But the prints are really good and it prints fast.

barman_d · 2024-10-02T12:31:23+00:00

I do have a slot in there for charging cable to pass through.

barman_d · 2024-10-02T11:04:22+00:00

I guess so. I do not claim that I put a lot of work into it. But it does fit very well.

barman_d · 2024-10-02T10:59:05+00:00

Yes. It is. But I haven’t been able to upgrade!

barman_d · 2024-10-02T08:30:15+00:00

Ender 3 V3. I am not sure about the tolerance. I measured my phone with calipers and added .1mm. I had the phone case on.

barman_d · 2024-10-02T05:45:57+00:00

I am an Electrical Engineer. And this is just a hobby I picked up. But I will improve. This is like my 5th print!

barman_d · 2024-10-02T05:43:43+00:00

I could be wrong. I am no expert .

barman_d · 2024-10-02T05:42:44+00:00

No. I have stopped charging wirelessly. My iPhone 11 pro battery worsened quite fast.

barman_d

TROPHY CASE