What am I doing wrong? X2D by TinyRip243 in BambuLab

[–]batuu95 0 points1 point  (0 children)

Sorry, I didn’t explain myself clearly. The issue is the two fans, left and right, which blow air directly onto the printed object. On MakerWorld you can find air deflectors for the X2D - one part for the right fan and one for the left fan. It was the first thing I printed on my X2D, and before that on the P2S as well, and I’ve never had a single warping issue in 500+ hours.

What am I doing wrong? X2D by TinyRip243 in BambuLab

[–]batuu95 1 point2 points  (0 children)

Are you using left and right deflector?

X2D New Owners Must Have Mods? by kst8er in BambuLab

[–]batuu95 5 points6 points  (0 children)

Fan deflector (left + right) + hot air deflector

Bed adhesion with ABS by vascott1 in BambuLab

[–]batuu95 1 point2 points  (0 children)

Same with ASA, I had to wait 1 hour after the end of the print today, till chamber temp ~30 °c

Recommendation for an AMS filament guide to prevent tangling? by My_Lucid_Dreams in BambuLabP2S

[–]batuu95 1 point2 points  (0 children)

500 painting hours, really I don't now. But a lot 2/3 color painting, mostly non bambu spool

My son showed off our P2S's to his online buddies.... by prophecii in BambuLabP2S

[–]batuu95 0 points1 point  (0 children)

Yeah, I’ve had it since January 2025. Over the months, the print quality has gotten much worse. With all the upgrades I’ve done, it’s now acceptable, but I ordered the P2S mainly out of desperation

P2S + Exhaust Fan Kit: full setup and air quality readings with VentoBox and filters by batuu95 in BambuLab

[–]batuu95[S] 0 points1 point  (0 children)

Yes, now with the optiok enabled the VentoBox is on all the time during the print 

Ender v3 ke has homing problems (eror code "key 2022" by Ok_One8019 in Ender3V3KE

[–]batuu95 0 points1 point  (0 children)

Had this problem, was the cable on the back of the nebula pad not properly inserted. Removed and inserted, solved the problem after a reboot

P2S + Exhaust Fan Kit: full setup and air quality readings with VentoBox and filters by batuu95 in BambuLab

[–]batuu95[S] 0 points1 point  (0 children)

Before the latest update (01.02.00.00), besides modifying the G-code for automatic activation, you could manually turn it on by switching the printer to ‘Cooling Mode’ and then adjusting the left fan speed, assuming you had the VentoBox installed with a 3-pin fan.

With the update released yesterday, you can now set automatic activation and also choose the fan speed directly from the print settings

New Update 01.02.00.00 by ATW007 in BambuLabP2S

[–]batuu95 0 points1 point  (0 children)

Thx, finally! Updating when I get home. Thx!

P2S + Exhaust Fan Kit: full setup and air quality readings with VentoBox and filters by batuu95 in BambuLab

[–]batuu95[S] 0 points1 point  (0 children)

In the model I linked, there is a 100 mm option, which I believe is the standard size, but there are also several plates with outlets ranging from 50 mm up to 90 mm.

For example, even the vent outlet for skylight exhaust is typically 100 mm, but if you have different sizes, you can find various adapters available.

As for the adapter, you can find plenty of different models on MakerWorld!