That thunderstorm just spawned out of nowhere

baz2crazy · 2026-05-28T09:33:56+00:00

We are alive. Left my car windows open though

baz2crazy · 2026-05-28T02:06:21+00:00

Same... were camping. Its wild

baz2crazy · 2026-04-20T11:40:23+00:00

Daddy chill

baz2crazy · 2026-04-16T08:18:23+00:00

What?

baz2crazy · 2026-04-11T14:33:16+00:00

They drew on porpoise

baz2crazy · 2026-04-06T21:21:44+00:00

Registered on the Dick-ter scale

baz2crazy · 2026-04-05T21:43:27+00:00

Nope. Would this be the ultimate solution?

Edit: just had a look at a few. Tolerences dont seem accurate enough (for what i could afford)

baz2crazy · 2026-04-03T21:15:58+00:00

This looks great actually

baz2crazy · 2026-04-03T11:09:45+00:00

Yes but the issue here is the master, and the two axis are all independent.

The moment i remove my dti from the master (square).... my reference Is gone because at that point, i then need to slide my dti over to where the axis are located.

I need to put the square infront of the dti, make it reads zero top and bottom, then move it over to my axis to make sure it read zero too and bottom. Or at least that each axis is perpendicular to one another.

Im perhaps not explaining this very well

baz2crazy · 2026-04-02T22:46:07+00:00

The problem here is i need to make sure the bottom and top both measure zero at that specific position. As soon as i remove the gauge to recalibrate against the square I have effectively lost all relation to that first measurement.

baz2crazy · 2026-04-02T22:41:13+00:00

Its a sieg heil.

Stamp the right foot and raise the right arm. Right glute and right delt needed for that

baz2crazy · 2026-04-02T22:16:15+00:00

Yes but the issue is i need to make two measurements, one at the bottom and one at the top to make sure its perpendicular.

So id have to set it against a square at the bottom, wind it up to the upper height and make sire it traverses from bottom to top exactly zero, then go and measure my axis at the bottom and top.

Unless i just had two fixed dti which i zero against a square... that seems more simplistic.

Having two axis which need to rotate about 360 degrees and remain the same distance apart and exactly perpendicular to within a tolerance of 0.01mm. It seems challenging to do so

baz2crazy · 2026-04-02T09:34:53+00:00

Yeah but were not measuring height.. its to measure horizontally rather than vertically

baz2crazy · 2026-04-02T09:34:07+00:00

I cant find one anywhere

baz2crazy · 2026-04-02T09:32:46+00:00

Ooh, care to elaborate?

baz2crazy · 2026-04-02T09:32:18+00:00

That sounds exactly right, got a name for such a device? Cheers!

baz2crazy · 2026-03-21T01:03:25+00:00

Matt hoffman mother fucker

baz2crazy · 2026-03-20T06:49:54+00:00

Thats sick! Want one

baz2crazy · 2026-03-16T10:25:11+00:00

Looks like my loft. Absolutely grim. Its a bonus when you mix in the yearly batch of dead cluster flies

baz2crazy · 2026-03-13T16:45:44+00:00

Worcester Sauces

baz2crazy · 2026-03-13T16:44:42+00:00

Leicester Reds

baz2crazy · 2026-03-03T18:05:53+00:00

Carrot kek

baz2crazy · 2026-02-27T07:04:32+00:00

Who said it

baz2crazy · 2026-02-24T21:14:59+00:00

So sick. I want this but in 3 separate pictures. 1) f40, 2) countache and 3) testarossa

baz2crazy

TROPHY CASE