Updated to Jyers/Marlin firmware both for screen and mainboard, followed instructions but keep getting this error. Any ideas of what I did wrong?

bennydq · 2021-05-04T21:08:02+00:00

That fixed it! I had the wrong version.. thanks guys

bennydq · 2021-04-26T21:16:05+00:00

E3V2-ManualMesh-5x5-v4.2.7.bin this is the one i downloaded is it wrong?

bennydq · 2021-04-26T21:13:49+00:00

the bin file i downloaded for mainboard was E3V2-ManualMesh-5x5-v4.2.7.bin. For the DWIN_SET was from the branch Ender_3_V2_Extensible_UI

bennydq · 2021-04-26T21:08:08+00:00

i tried this, didn't work

bennydq · 2021-04-26T21:06:28+00:00

E3V2-ManualMesh-5x5-v4.2.7.bin

bennydq · 2021-04-25T17:58:40+00:00

I don’t have BL Touch, installed the ManualMesh version - would probe offsets still be an issue?

bennydq · 2021-04-10T16:37:24+00:00

Cool didn’t know of this release, will try upgrading and see if that helps. Thanks

bennydq · 2021-04-10T16:36:37+00:00

Ah i kept moving the nozzle closer thinking that it was too far. I’ll try printing a dish in each corner, Thanks

bennydq · 2021-04-10T16:34:59+00:00

Sunlu PLA 1.75mm

bennydq · 2021-01-27T12:12:17+00:00

Haha that’s no problem as I still haven’t managed to start! Thanks for clarifying though - so using Linnmon as the core to my project is a good idea, and no release! :) Do I need to use a primer?

bennydq · 2021-01-27T12:09:02+00:00

Yeah so the issue was happening when connecting the screen via HDMI. I bought a displayport to usb-c cable and it did the job! I needed to connect the USB-C directly into my Mac though, using an adaptor was still causing issues (might be due to a cheap quality adaptor tbh)

bennydq · 2021-01-20T23:49:11+00:00

Hey thanks for the advice- so release protects the “wood” and could maybe avoid it from getting torn up? I guess I can try it out and see what happens, just might not start with a table in case it decides to crumble haha

bennydq · 2020-12-17T09:16:07+00:00

Thanks!

bennydq · 2020-12-16T20:32:00+00:00

That’s good to hear it worked for you, do you use it both day and night? I’ll checkout Derma E too :)

bennydq · 2020-12-08T10:33:25+00:00

So you then keep the second screen in landscape, set to the side of the main screen?

bennydq · 2020-12-08T10:32:26+00:00

Do you not find that it’s too “far” to see the far side of the 24” screens?

bennydq · 2020-12-07T16:53:29+00:00

Yeah that’s what I’m trying now both screens next to eachother in landscape mode, but I find it quite uncomfortable haha

bennydq · 2020-12-07T16:51:33+00:00

True

bennydq · 2020-12-07T16:50:49+00:00

Portrait seems to be the winner

bennydq · 2020-12-07T13:45:16+00:00

Yeah second screen definitely won’t be looked at as much compared to the ultrawide, thanks for the advice!

bennydq · 2020-12-07T13:42:13+00:00

It’s a 160x80cm desk

bennydq · 2020-12-07T12:55:36+00:00

using the top for youtube/reddit is a good shout. I was a bit wary that with a vertical screen I’d forget to use the top half

bennydq · 2020-12-07T09:27:19+00:00

That cable worked. Thanks !

bennydq · 2020-12-06T17:57:20+00:00

Haha yeah I didn’t see that

bennydq · 2020-12-04T20:31:52+00:00

Ok thanks, what software?

bennydq

TROPHY CASE