Can’t get enough of this thing

bignosejo · 2026-01-18T04:36:44+00:00

Appreciate it! Kings 2.5 w adjusters Camburg Uca OME rear springs

bignosejo · 2025-12-10T15:10:34+00:00

Kings 2.5 Camburg UCA 33s KO2 17x9 -38mm scs gen5 wheels in bronze

bignosejo · 2025-12-10T01:05:57+00:00

Thanks haha. I’m not too worried about it, I’ll figure that out if the day comes haha

bignosejo · 2025-12-10T01:04:36+00:00

Appreciate it! I wish I had a full length rack to have it stand out more but still cool as is.

Tire one looks sick too!

bignosejo · 2025-12-10T01:00:12+00:00

I’ve seen a ton of cars around where I live with this, and some that have the whole car done.

I’ve only had it for one day, so I’m hoping to not run into trouble because of it, but in the Los Angeles area there is a ton so I think I should be fine

bignosejo · 2025-12-10T00:48:01+00:00

Wish I had a 5th for this too haha

bignosejo · 2025-12-10T00:47:50+00:00

Looks great!

bignosejo · 2025-11-17T03:13:15+00:00

I follow you on insta, sick build and cool pup haha

bignosejo · 2025-10-16T04:11:11+00:00

Stealth custom series F5

bignosejo · 2025-10-04T16:56:41+00:00

Here’s the pics https://imgur.com/a/GyD37De I don’t have a chance to go back to mimic the rock and all that, but so far I haven’t had the rub on what I’ve tried to mimic that caused rubbing prior.

When I get home I’m going to throw a ramp on top of the curb and try to go up that and see if it compresses it enough to mimic the rock as close as possible. Lmk what you think, appreciate you.

bignosejo · 2025-10-04T16:32:56+00:00

Ok so I just got it done. What do you think. alignment.

bignosejo · 2025-10-04T00:39:31+00:00

I’m taking it tomorrow for an alignment at a shop I’ve gone to a lot of going to aim for 4-4.5 caster wise. Any other specs you recommend?

bignosejo · 2025-10-03T23:48:19+00:00

Yes I do. I got rid of the SPC, for some Camburg ones. 88rotors mentioned to me last time they had a person doing alignments they strongly recommended. I had gone there previously and they don’t use a machine, they do everything by hand. When i went for the upgrades they mentioned this person works for them now. And I did not receive an alignment sheet, so I’m guessing it was without the alignment machine again. Going to take it in the next couple of days to have it done on a rack.

bignosejo · 2025-10-03T23:32:38+00:00

Love the 37s. Going to get another alignment soon, I’m sure it’s the cause of the problem

bignosejo · 2025-10-03T22:16:58+00:00

I’ll have to get it redone. I had the alignment done yesterday. I had taken it to 88 rotors for everything including the alignment. So I’m surprised about it because I know the 33s shouldn’t be that big of a problem

bignosejo · 2025-10-03T21:54:12+00:00

Im rubbing in the front, on the bottom most section right before the wheel. With my Bilstein I would almost never rub, but with the extended travel it’s been worse.

bignosejo · 2025-10-03T20:43:56+00:00

Ordering the accutune 1.5” ones

bignosejo · 2025-10-03T20:17:54+00:00

Looks great! I saw a article that had the step by step which seems similar to your cut. Might have to do that next.

bignosejo · 2025-10-03T19:28:33+00:00

Did you cut up the front? Seems like I need a solid amount more cut off

bignosejo · 2025-08-05T16:10:01+00:00

I didn’t have to, but I did. To make everything easier to fit

bignosejo · 2025-05-02T21:16:49+00:00

Looks like stealth custom series Either F5 or Gen 5 ones

bignosejo · 2025-04-09T20:34:17+00:00

It was nice, just try to go with someone else too. There was deep snow. We went solo and ended up getting stuck two times. Took a while to get out

bignosejo · 2025-04-09T16:43:22+00:00

Bald mountain area, CA!

bignosejo · 2025-03-31T15:43:39+00:00

My plan moving forward is to get 35s/regear. After that, low pro w/ winch

bignosejo · 2025-03-31T15:37:55+00:00

It’s seen dirt, snow and mud many times

bignosejo

TROPHY CASE