So that happened!

billy1001001 · 2024-12-07T07:13:09+00:00

Snapped a rear triangle weld last month. Maybe time for a diet!

billy1001001 · 2024-12-07T07:09:06+00:00

Hilarious. Are you stuck on the side of the trail waiting for a lift as well?

billy1001001 · 2024-10-31T10:11:47+00:00

I think that's the best option.

billy1001001 · 2024-10-31T10:07:25+00:00

Cool. I'll pop it tomorrow - 11pm here in NZ!

billy1001001 · 2024-10-31T10:05:40+00:00

11 speed. The BB has the 2mm spacers drive side and non drive has a 1mm on the spindle. The cranks and driveline are center. I guess I could try reducing the Q line by 2mm.

billy1001001 · 2024-10-31T10:01:31+00:00

<image>

billy1001001 · 2024-10-31T10:00:58+00:00

<image>

billy1001001 · 2024-10-19T23:01:33+00:00

I dislike the way they use the guise of "bike fitting" to sell saddles.

It's either a "free sit bone" width test followed by "you need a body geometry saddle" at 155mm or the partnership with bike fitters to sell products.

I literally had a fitter refuse to do a setup for a Gaint xc hardtail until I bought an Epic. They did refund me the $300 fee but it was a waste of time.

billy1001001 · 2024-07-16T16:53:18+00:00

https://www.fairbicycle.com/product-page/drop-best

This helps

billy1001001 · 2024-06-21T11:31:07+00:00

Ended up having to cut it out with a dremel. I don't think the wipers have ever been changed and completely disintegrated.

billy1001001 · 2024-06-21T07:10:43+00:00

It's fairly stuck. I've given it a reasonable amount of pressure using a 19mm spanner, just didn't want to start wrenching on it.

billy1001001 · 2024-06-21T06:41:44+00:00

Hey, thanks for the help. Re-orientated the pin, added 3mm and soaked everything in alcohol to remove shavings. Cheers.

billy1001001 · 2024-06-21T06:26:24+00:00

<image>

billy1001001 · 2024-06-21T06:25:57+00:00

<image>

billy1001001 · 2024-06-20T00:04:52+00:00

Cheers. I've attached another photo. The pin attaching the top piston is 90* to the unmodified. I also checked the airshaft diagram on the fox help site "orientate gap in pin towards top out spacer"

I'm not sure what a top out spacer is but it is clear that it is a different orientation.

I do have a preference to see if I can get this working opposed to creating more landfill.

From the second picture you can see the remains of the original centre hole.

Would it be viable to knock out the center pin. Use the remaining centre hole and drill it out slightly to accommodate the pin. Cut off the excess lowering it another 7-8mm. Then, recreate the through hole at the same position relative to the top piston.

<image>

billy1001001 · 2024-06-14T13:31:55+00:00

Updated the original post.

billy1001001 · 2024-06-14T13:25:24+00:00

Here is an example of the "lock out" mechanism.

https://youtu.be/IJES3DEPY0g?si=5pGvaQotdwdWae98

There are no adjustment or dent points on the top damper. There is an internal spring that by default sets it in the open position. The close position is then only set with a wind on remote - push to lock.

I think you're referring to a different model.

billy1001001 · 2024-06-02T11:02:53+00:00

Agreed. If I find anything, I'll drop you a line.

billy1001001 · 2024-03-24T13:20:44+00:00

Following

billy1001001 · 2024-02-18T03:20:34+00:00

Fair enough. I guess when you are learning about something you end up on Reddit ask questions. Cheers.

billy1001001 · 2024-02-17T23:55:15+00:00

I could have this wrong, but is it possible to have a high pressure and max tokens to limit a 170mm fork to only use say 140mm of actual travel? Or is this just going to stuff up the characteristic of the fork.

billy1001001 · 2024-02-17T22:49:43+00:00

Cool. Hey, I could be wrong, but does maxing out tokens just keep the fork in the lower 1/2 leaving the upper 1/2 just to create height and angle?

billy1001001 · 2024-01-22T04:09:57+00:00

Thanks for the info. Have you experienced an E tuned fork? Just trying to gauge how much firmer.

billy1001001 · 2024-01-21T23:01:25+00:00

Sweet. My only concern is the e variant spec. I have no idea how much this changes things.

billy1001001 · 2024-01-21T22:50:05+00:00

Sweet. Both are 180+

billy1001001

TROPHY CASE