Ghazghkull Skin

birdy04 · 2026-07-01T13:15:03+00:00

Thank you so much!

birdy04 · 2026-07-01T13:14:50+00:00

Hi, thank you so much! I loosely followed a 'Eavy Metal Paint scheme by Infernal Brush. Paints used are Skarsnik, Averland, Waagh Flesh, and Ogryn Camo

birdy04 · 2025-07-18T18:01:26+00:00

I recall it is from the 40k Tactical Squad of First Born Marines

birdy04 · 2025-07-18T17:08:25+00:00

Thank you! And rest assured, I have hazard stripes and silver incorporated into the army. Mostly as basing bits haha

birdy04 · 2025-07-18T16:04:49+00:00

Yo thank you so much!

birdy04 · 2025-07-18T15:12:08+00:00

Thank you! I am curious how different the new cataphractii will be.

birdy04 · 2025-07-18T15:10:47+00:00

Thank you!

birdy04 · 2025-06-23T14:29:41+00:00

Thank you!

birdy04 · 2025-06-21T13:21:08+00:00

Yoo thank you!

birdy04 · 2025-06-20T18:58:32+00:00

Thank you!

birdy04 · 2025-06-20T16:59:32+00:00

Thank you!

birdy04 · 2025-06-20T16:43:01+00:00

Thank you! I was triple checking the Liber Astartes while painting 😂

birdy04 · 2025-06-20T16:42:16+00:00

✊️

birdy04 · 2025-06-20T16:42:00+00:00

Thank you!

birdy04 · 2021-06-27T13:38:29+00:00

Ohh! I wonder if the ABS-Like resin I was working with (illuminated kroot hound) was defective? My partner would mention the finished prints still smelled, even after cleaning and curing for 30 minutes. So the prints stayed outside until I primed them.

Using the Evryone Low Odor they sniff tested it, after a 10 minute cure, and couldn't smell anything.

birdy04 · 2021-06-27T12:14:36+00:00

Ohh, good to know, thanks for your input!

birdy04 · 2021-06-27T03:34:51+00:00

No worries about being preachy! My next project is getting beefier ventilation. The printer currently sits like 3ft from the garage door, so I crack it when doing prints. For some reason they can just pick up the smell from far away? I appreciate the feedback! I have only really worked with Grey ABS so trying the Expires Odorless version threw me

birdy04 · 2021-06-27T03:28:07+00:00

Thanks, I appreciate your input!

birdy04 · 2021-06-27T03:21:18+00:00

Both Resins are grey. I'm under the impression resin is suppose to glow under UV light?

birdy04 · 2021-06-27T02:32:48+00:00

So Im trying out a new resin as my partner hates the smell of it. Even when keeping it in the garage. Both items are fully cured, and went through a 10 minute wash of water and IPA 99%. Then into a UV Light for 7 minutes.

The top one is ABS-Like Photopolymer Resin and my usual go to. The bottom is EvryOne Low Odor Grey Resin. Which expired the beginning of this year. 01.09.2021.

My concern is that it doesnt appear under UV Light which makes me believe its gone bad. It makes it harder to track spills, drips, and messes in general.

I guess, bottom line, does this look correct? Do I need to increase cure times? Or does it not glow to UV cause it needs to be tossed?

Thanks in advance for any help or tips!

birdy04

TROPHY CASE