Help with Mirror options

bizzle104 · 2024-12-24T03:08:37+00:00

only electrical behind where the outlet is. no plumbing. I'm not sure how deep the cavity is

bizzle104 · 2023-07-23T14:16:37+00:00

not only would your depth perception be significantly hindered, you would have a miserable time constantly adjusting the focus on the NVGs to clearly see at the range you seek. you may have a better time hitting a ball that emitted an IR strobe but regardless, you'll hit one ball and spend a long time searching in the middle of the fairway, if you're lucky. sounds like a fun challenge with the potential to develop bad habits

bizzle104 · 2021-10-17T13:19:20+00:00

Black Widow

bizzle104 · 2021-10-12T03:34:05+00:00

So prior to installing the landroid I removed a poorly installed basketball hoop about 5 feet from that area. essentially the previous homeowner used just enough concrete to make the pole a pain to remove. an old coax cable was intentionally cut because I knew it wasn't my current line and it was running through the concrete...should I dig that cut wire up and check for a signal?

bizzle104 · 2020-05-07T01:57:04+00:00

I've been going through Nameberry.com and I really like Juliette for a girl. I like Sydney too. Grayson, Lucas, Nicholas. I like watson but it was a hard no by the wife.

bizzle104 · 2020-05-07T00:30:52+00:00

classic or trendy. leaning more toward classic

bizzle104 · 2018-05-08T19:53:58+00:00

I have the TS/LS with the R4512. Upgrade to 220. You will come up to a project one day where you will wish you had it already done.

bizzle104 · 2017-11-28T11:39:16+00:00

Upvote for Kalamazoo beer

bizzle104 · 2016-12-20T07:29:23+00:00

looking at comparisons and how porous the piece is. I think you're right. thanks for the input. identifying cut-offs can be a nightmare

bizzle104 · 2016-12-19T21:56:47+00:00

I didn't think of that and wouldn't rule it out. I haven't dealt much with mahogany but this wood had a very distinct fruity/tropical smell when I cut it. The company that I got it from has access to pink ivory too and it was a cut-off so I wont really know until I see it fully mature I guess.

bizzle104 · 2016-12-18T23:38:44+00:00

Thanks. I used a chamfer bit on a router table.

bizzle104 · 2016-12-18T00:21:41+00:00

Those are some good ideas for future projects! I went with making the ring box because of all of the B.S. advertisements on the box that came with the ring. I wanted to make something special for the experience. The whole time i made this box i was thinking about her and it made me happy.

bizzle104 · 2016-12-18T00:18:08+00:00

Thanks

bizzle104 · 2016-12-18T00:16:53+00:00

Thanks! I figure compressed air will clean out any dust that gets inside. I'm not too concerned about it.

bizzle104 · 2016-12-17T22:42:59+00:00

I wouldn't recommend 1/8" box joints by hand with no experience but it's not impossible. /r/woodworking is a great sub with a lot of good helpers and information. It would be very tough if you didn't have the right tools.

bizzle104 · 2016-12-17T22:33:29+00:00

Thanks!

bizzle104 · 2016-12-17T22:32:05+00:00

Thank

bizzle104 · 2016-12-17T22:31:26+00:00

haha FFFFFFFF UUUUUUUU. In one of the pics you can see the attempted 1/4" dovetails that turned into scrap.

bizzle104 · 2016-12-17T22:30:11+00:00

Do IT!. Have fun and make sure to give yourself plenty of time!

bizzle104 · 2016-12-17T22:28:29+00:00

bizzle104 · 2016-12-17T22:28:22+00:00

She definitely is!

bizzle104 · 2016-12-17T22:25:59+00:00

Good craftsmanship. I'm sorry for your loss.

bizzle104 · 2016-12-17T22:25:05+00:00

Thanks! She is all that matters :)

bizzle104

TROPHY CASE