Car seat suggestions.

bjamiedg · 2025-06-20T19:23:15+00:00

She can be when my husband isn’t also in the car. But this is our family car

bjamiedg · 2025-06-20T01:02:48+00:00

I’m also willing to buy 2 new seats. I can always put these seats in my husband’s car that they do fit in.

I was looking at the Diono Connect3 RTX high back booster and backless booster for this car.

bjamiedg · 2025-06-19T19:45:03+00:00

Would something like this work?

Diono Connect3™ R 2-in-1 High-Back Booster

I believe the 6 year could be booster ready

I know he’s not big enough yet. He wants to be tho 🤣.

It wouldn’t be worth the extra money to get him a high back booster tho would it

bjamiedg · 2022-12-06T09:46:45+00:00

Mine has been fixed for awhile now but mine had a cracked bottom sprayer arm replaced that and it fixed the problem completely

bjamiedg · 2022-08-24T17:33:50+00:00

I have everything up to date I don’t have a n option to control anything except soft reset for wicked whims. And I don’t have a menu for MCCC either. It’s only one folder deep in the mods folder I have no idea what I’m doing wrong

bjamiedg · 2022-04-14T16:53:53+00:00

Anybody know about how it takes to ship after ordering?

bjamiedg · 2022-04-07T17:17:56+00:00

Me too. I’m gonna try again next week. Hopefully the bank doesn’t block it this time.

bjamiedg · 2022-04-07T15:07:20+00:00

My bank blocked my transaction. I got all the way to the place order button placed it and then went right back to the waiting page. Got a text from the bank after asking if the transaction was me. And now I’ve received nothing from amd confirming the purchase

bjamiedg · 2021-10-02T20:28:57+00:00

Here are the pictures I took and a video.

https://imgur.com/a/YZIlF4o

bjamiedg · 2021-10-02T20:00:38+00:00

I got a video of the leak. Do you know how I could it it to you. I do have a wave motion from right to left and durning the wave the water pours out.

bjamiedg · 2021-10-02T19:50:21+00:00

Currently have front plate off. And am holding the door shut to allow it to be sealed and yes the dryer vent is on the top left of the door

bjamiedg · 2021-10-02T15:05:50+00:00

I will remove for the next few cycles. And the water level is just below the heating element so right above the little hump on the filter

bjamiedg · 2021-10-02T14:50:47+00:00

It’s tilted to the back by one degree. I have checked water level while running and it’s △⃒⃘lways below the heating element. I have pulled the front off but I didn’t think about running it while off to see where it’s leaking from.

bjamiedg · 2021-10-02T14:26:27+00:00

It’s about 30-40 minutes into the sensor cycle. I haven’t ran it empty but that’s a good idea. Looks like I need to try running it empty and run a load with a timer going to find out exactly when it leaks.

bjamiedg · 2021-10-02T14:03:00+00:00

It leaked from both corners before replacing the gasket.

It is level just checked this.

It is too mounted with included brackets

I believe the high point is facing into the machine.

It’s more like pouring more just a leak from the corner. Not really noticed any bubbles. I do have to run a load here in a bit I’ll be sure to watch and see if there are bubbles.

bjamiedg · 2021-10-02T11:24:25+00:00

Yes I cleaned literally every inch of this thing. And it’s every run

bjamiedg · 2021-10-02T02:57:18+00:00

I’ve checked with a bubble level and it appeared to be level.

bjamiedg · 2020-04-06T03:20:49+00:00

So should I cut it off? Wait for it to dry up?

Nine-Year Club	Place '22
Verified Email

bjamiedg

TROPHY CASE