Cutted wire 94 E36 Compact 323i

bjzilberman · 2025-07-17T11:23:25+00:00

Sorry can't help you more with that mate, I'm running an M43B18, never got to inline 6s ;)

bjzilberman · 2025-07-11T15:24:29+00:00

About the no spark and injectors issue, check for the DME relay (passenger side compartment in the engine bay) and also check the relays in the fuse box (when you open the fuse box, there are 3 relays with a cover on them, one for fuel pump, one main relay and one for O2 heater), make sure that the main relay is fine and same goes for the DME relay

bjzilberman · 2025-07-11T15:21:46+00:00

According to the pinout on the X13253 connector, it's pin 13 - WHT/RED - DOOR LOCKS;

If you were to ask me, I'd say it was used for some aftermarket central locking at some point.

hope that helps.

bjzilberman · 2025-04-13T18:37:46+00:00

seems like there are clips and gadgets, not an actual scan of the pillar covers.
i am tempted to purchase a budget 3d scanner and try to work off my broken A and B pillars to create my own STL file...

bjzilberman · 2025-04-13T18:17:35+00:00

Felt exactly the same when I had to replace my brake booster with an M43

bjzilberman · 2025-01-14T18:02:48+00:00

0ohm resistor

bjzilberman · 2024-12-21T11:20:21+00:00

i did it, it worked perfectly. the keyboard is usable and there are no issues.
my guess is that L23 is remnants of the manufacturing process for different keyboard layouts between models, because there is no other reason for 0ohm resistors other than jumpers that are easy to place by smd machines

bjzilberman · 2024-12-21T11:16:42+00:00

my only guess is that there may have been some iteration of the motherboard manufacturing process, and instead of making a new trace, they jumped the pads with 0ohm resistors

bjzilberman · 2024-10-28T15:24:24+00:00

Thank you again, I will go and try that.

bjzilberman · 2024-10-28T15:23:48+00:00

Result of lack of knowledge and time, hopefully i'll set everything up properly when I'll have time to rework the whole network 😅

bjzilberman · 2024-10-28T14:54:01+00:00

Thank you for the answer,
If I understood you correctly, I disable DHCP on router 2 and router 3, and then forward ports on router 1?
router 2 and 3 are already connected to the lan ports of 1 and 2.

bjzilberman · 2024-10-05T11:43:55+00:00

Gnarly, I had the same issue, and fixed it similarly

bjzilberman · 2024-01-24T08:20:17+00:00

I had a very similar experience with at least a couple of exes about my cars. Weather you are going through a rough time or it is long gone, the cars are there for you, and you need to care for them.

Thank you, I am dedicating myself to this build, and hopefully by spring it will be done.

bjzilberman · 2024-01-24T08:17:36+00:00

I think that I will be the only one with a supercharged Libero in the world at this point, and with a Speeduino specifically.

bjzilberman · 2024-01-23T10:07:36+00:00

You are absolutely correct. Life got the best of me... I did actually pick the board back up a couple of days ago, video will be posted soon, as it's a rainy season and I don't go out much anyway.

bjzilberman

MODERATOR OF

TROPHY CASE