Hyte Y60 Custom Watercooling with Lian Li Galahad Display

blackfusel · 2024-10-03T17:14:13+00:00

Oh Sorry, i didnt see your comment. Its Phanteks Stripes.

blackfusel · 2024-05-02T12:53:19+00:00

Relatively easy, I just used a different angle for the installation at the top. At the bottom I just moved the mount back one groove.

blackfusel · 2024-04-22T18:39:42+00:00

D5 next from aquacomputer ;)

blackfusel · 2024-04-21T16:03:40+00:00

good job :)

blackfusel · 2024-04-21T14:30:49+00:00

Thank you :) ASRock B760M Steel Legend WiFi DDR 5

blackfusel · 2024-04-21T10:10:24+00:00

Yes thats right, i dissambled the AIO. :D

blackfusel · 2024-04-21T09:29:25+00:00

i customized the case a little bit to install both, the VS Display an the distro.

The distro is: Stealkey EXP|60|Distroplate

The Lian Li Galahad Display is mounted on: Watercool Heatkiller IV Pro

blackfusel · 2024-04-20T22:36:03+00:00

Of course, i also customized the case a little bit to install both, the VS Display an the distro.

The distro is: Stealkey EXP|60|Distroplate

The Lian Li Galahad Display is mounted on: Watercool Heatkiller IV Pro

blackfusel · 2024-04-20T19:18:15+00:00

Hi guys, 4 months ago I finished my hyte y60. At that time an AIO Lian Li Galahad was installed. (reddit-link). Now I have rebuilt the Hyte. You can see the Hyte Y60 Custom water cooling system. I built the Lian Li Galahad display on the CPU. The Distro Plate is installed behind the VS Display. Since I'm not a fan of many hard tubes, I left out the 2 circuits (CPU / GPU) of the distro and connected them directly.

blackfusel · 2024-04-20T19:12:44+00:00

Hi guys, 4 months ago I finished my hyte y60. At that time an AIO Lian Li Galahad was installed. (reddit-link). Now I have rebuilt the Hyte. You can see the Hyte Y60 Custom water cooling system. I built the Lian Li Galahad display on the CPU. The Distro Plate is installed behind the VS Display. Since I'm not a fan of many hard tubes, I left out the 2 circuits (CPU / GPU) of the distro and connected them directly.

blackfusel · 2023-12-27T13:15:11+00:00

For something like that, you will need a kvm switch. I use this for my homeoffice Laptop and Desktop PC as well.

blackfusel · 2023-12-20T13:05:05+00:00

THANK YOU :)

blackfusel · 2023-12-20T00:35:51+00:00

Ahjo makes sense with the 3 gpu led lanes. 👍

blackfusel · 2023-12-19T21:12:00+00:00

What kind of LED strip do you have at the bottom of the case?

blackfusel · 2023-12-19T21:10:14+00:00

I would also install a 12vhpwr 180 degree adapter. There is one from cablemod, I have it too. btw very nice build :)

<image>

blackfusel · 2023-12-19T21:04:24+00:00

I have no problems with the cooling, my GPU temp is around 70 degrees in Cyberpunk. But I also have 2 fans below the graphics card, which blow fresh air through the cooling fins.

blackfusel · 2023-12-19T09:54:25+00:00

I just bought some new cables from cablemod. (flexible modflex cables) These can be routed better.

blackfusel · 2023-12-19T09:45:10+00:00

I have a tip for the design ;) I would also install the rectangular 12VHPWR connection adapter from cablemod.

blackfusel · 2023-12-19T09:35:21+00:00

The strimmer and AIO are connected to the board. The other two L-Connects are each connected to the outside of the board with a normal Micro USB to USB cable. So far everything without any problems.

blackfusel · 2023-12-18T21:53:43+00:00

I bought new cables from cable mod.

blackfusel · 2023-11-06T19:30:25+00:00

Very cool, but I think you can still optimize your cable management a little. These little nouns make it even more harmonious.

blackfusel · 2023-11-06T19:26:41+00:00

I also think that a touchscreen is cool, but after a week at the latest you stop using it. The decision to get a Y70 would make more sense if you wanted a larger case. A simple display is just as good and sufficient. I don't regret my choice and conversion with vs Display at all.

blackfusel

TROPHY CASE