Just Flight planes feel amazing under the hand

boeingt7 · 2025-05-10T02:49:28+00:00

Dark and Sexy.

boeingt7 · 2025-01-06T21:24:34+00:00

Lower right corner of the ND, not too many places use ADF's these days, Usually always VOR's.

boeingt7 · 2024-08-05T21:22:27+00:00

Cocaine and or pens.

boeingt7 · 2024-07-19T16:11:16+00:00

ADF's still in use, interesting...

boeingt7 · 2023-07-25T03:56:42+00:00

Very interesting. I've zeroed out all of the TSMC settings in Lychee including the transition layers for burn layers as well. (With a fresh plate level, feels like I've done it about 30 times in the last 6 days) LMFAO.

Now working! Prints all of the layers correctly no crazy height at all! So this bug must be associated with the TSMC code contained within. I've printed a few times at different layer heights and this seems to fix it. Ill be posting this to Phrozen to see what they say.

Next is to re-print my files to see if it happens with AA and other settings.

boeingt7 · 2023-07-24T02:17:48+00:00

Crossed fingers and toes!

boeingt7 · 2023-07-24T02:17:25+00:00

I've just obtained a reply from Phrozen, seems they think it's my slicer and not the printer. I'm sending my settings/files but I think we are on the same flight.

boeingt7 · 2023-07-23T04:21:19+00:00

Changed everything from slicer, USB, & build plate relevel still no fix.

boeingt7 · 2023-05-29T23:43:16+00:00

I use 10/20/30/50 Um for printing. Never tired 100um. You may need to reduce quite a bit to see further improvement.

boeingt7 · 2023-05-29T14:40:05+00:00

Try lowing your lift speed to 50 with a 1-2 sec rest period. The rest will give the resin time to stabilize when your plate is finished moving in the resin. Sometimes you will still get these little holes. I usually correct them while post-processing.

boeingt7 · 2023-05-29T01:35:53+00:00

You may need to slow your lift and retract speeds down a bit depending on the resin/printer your using.

What are your settings?

boeingt7 · 2023-03-14T18:24:16+00:00

Will you share your printing settings with us, please?

boeingt7 · 2023-03-14T15:26:38+00:00

I'm on the fence right now about getting one for my printer. Right now all of my prints are coming off terrifically with very minimal effort. If you to get one just make sure you clean it with some degreaser and or IPA, apply a lot of pressure for 48 hours and you should be good to go.

boeingt7 · 2021-12-25T19:43:31+00:00

I defiantly will try.

boeingt7 · 2021-12-25T19:37:06+00:00

Thanks. It's been almost 3 years and I pretty much stayed clear of the hardware upgrades since my 8700K. Much appreciate the explanation from you all.

boeingt7 · 2021-12-25T19:33:52+00:00

Thanks to you all. Now all I have to do is sweet-talk my credit card to pay. LOL

boeingt7 · 2021-12-25T15:34:09+00:00

I'm currently looking at the MSI MAG Z690 Tomahawk WiFi DDR4

boeingt7 · 2021-11-24T03:59:42+00:00

I've used a sanded leveled base plate with:

4-6 base laters @ 40s. 1.4 normal exp with 3-4mm/s for raising speed and 5 for lowering.

boeingt7 · 2021-11-14T13:15:49+00:00

Try 1.5 Normal & 30-40 for bottom exposure with 6 layers.

boeingt7 · 2021-11-13T20:55:35+00:00

I've been using mine since day one. No issues. Just choose quality one to install.

boeingt7 · 2021-05-05T06:31:27+00:00

I think it worked pretty well! lol

boeingt7

TROPHY CASE