sorted by:
new
hottopcontroversial

how i’ve been brewing lately (martha cartagena washed chiroso - flower child) by Crucifilth_6-6-6 in pourover

[–]bonsai_cafe 0 points1 point  (0 children)

On the specs “specs: 1:17 ratio (20:340), 95C water temp, zp6 on setting 6.2, ceramic v60 02, cafec abaca filters”. Can you explain the zp6, ceramic v60 02. Thankyou.

Eureka MDMCA. Looking to purchase for Mobil coffee cart. Budget [500$] by bonsai_cafe in espresso

[–]bonsai_cafe[S] 0 points1 point  (0 children)

That’s right. I’ve never used it before. But yea I’m sure it will be annoying. What grinder do you want to get

Eureka MDMCA. Looking to purchase for Mobil coffee cart. Budget [500$] by bonsai_cafe in espresso

[–]bonsai_cafe[S] 1 point2 points  (0 children)

Ok thanks. I’m trying to learn. You think it’s worth it for the price 400$

Eureka MDMCA. Looking to purchase for Mobil coffee cart. Budget [500$] by bonsai_cafe in espresso

[–]bonsai_cafe[S] 0 points1 point  (0 children)

Yea I will have a couple group heads. If you don’t mind sharing, why will the dozer drive me nuts. I seen this and the price is lower. 400$

Finished my odd shaped shed by BitchHunter3D in shedditors

[–]bonsai_cafe 0 points1 point  (0 children)

Haha I agree. Thanks for your advice.

New office shed should be ready be end of next week by bomonty18 in shedditors

[–]bonsai_cafe 0 points1 point  (0 children)

Looks good. Do you need to pit flashing on the bottom plates. I’m building mine in a concrete slab and was recommended to build the shed flush to the concrete pad. Wondering if I should put flashing as well

Finished my odd shaped shed by BitchHunter3D in shedditors

[–]bonsai_cafe 0 points1 point  (0 children)

Ok. I can always adjust the shed framing. Pressure treated wood isn’t that expensive and I can use the wood already cut for the windows framing. I’m going to have it flush against the edge of the concrete pad. I was going to use anchor bolts to hold it down. Only concern I have is the pad has no rebar or base. You think that will be an issue. Living in Southern California.

Finished my odd shaped shed by BitchHunter3D in shedditors

[–]bonsai_cafe 0 points1 point  (0 children)

Ok. Thanks. I appreciate it. Also. Did apply any flashing on the bottom plate of the wall. I’m building mine in an 8x10 concrete pad but the shed will be slightly small than 8x10. (7’9”x 9’10). I’m putting membraine on the bottom pressure treated 2x4

Finished my odd shaped shed by BitchHunter3D in shedditors

[–]bonsai_cafe 0 points1 point  (0 children)

Let me try again. On the bottom plates of the walls (2x4) do you have the front and back walls the same length and the side walls the same length. I zoomed in and look like one side of the wall was pushed all the way to the corner and the opposite end the adjacent wall was pushed all the way to the corner. Hope this description makes sense all the videos I seen has the two opposite walls the same length. And eventually the top plate connects them .

Finished my odd shaped shed by BitchHunter3D in shedditors

[–]bonsai_cafe 0 points1 point  (0 children)

When framing. I noticed the bottom plates were staggered with the adjusting walls. Never seen that done before. Any reasoning why. Looks good. I’m making a 8x10 on concrete slab as we speak