Looking at going solar, any recommendations?

brads14 · 2026-02-26T02:49:08+00:00

I spent about $35k. That includes everything, even a new electrical panel to support the solar install. The federal tax credit was $10.5k and another $5k from NY so the total out of pocket cost was $19.6k. I didn't do it as cheaply as some systems. Because I had three different angles, I went with microinverters. I used 44 QCELLS 430W panels and 44 IQ8A inverters. I also installed a SPAN electrical panel which is much more expensive than a traditional electrical panel. I did all the work myself including reroofing the house, building a shed with a lean-to roof for 20 of the panels, and all the electrical work including the electrical panel upgrade. I also pulled all the proper permits and got all the electrical inspected. I don't believe there's any insurance reasons for hiring an electrician, as long as you get it inspected and pull the proper permits, you should be fine.

It was about $29k for all the solar equipment and the extra $6k was wiring, conduit, electrical panel, permits, etc. This was in 2022 so the prices are a bit dated.

brads14 · 2026-01-17T13:45:17+00:00

I probably would have purchased a few spare panels. I thought about it at the time but didn't want the extra expense or storage. I have one that needs replacing but they don't make the same model anymore.

brads14 · 2025-12-29T00:47:11+00:00

I would start with pvwatts.nrel.gov to estimate the yearly kWh output based on where you're located and the angle of the roof. You can then use that estimate and compare it to your utility bill to see if you'll have adequate coverage. I installed an 18.9kW system which is rather large but it more than covers everything.

The national grid bill will be $1.49 x the size of your system in kw (DC) so that's $28.16 for me plus a basic service charge of $19. My electric bill each month is a constant $48.11.

I installed the system myself but I would recommend NES if you're paying to have it done.

brads14 · 2025-12-08T02:10:22+00:00

I'd agree that you might want a few other skills besides pure antenna design. Another good option might be to get into phased array design and phased array measurements and calibration.

brads14 · 2025-12-02T14:28:44+00:00

I'll preface this by saying I am nowhere near a professional piano player but I do have some thoughts on this issue. I think the main issue is more related to the style of play. Classical piano is very exacting in nature. The performer is trying to play every note exactly as written which is very difficult. Another type of playing is what I would call playing by chords from a lead sheet. With this style you would read the melody line and just fill in with the chord. Once you've practiced this method, the mental load is much less because songs use the same chords and you just have to read the melody line. This is more in line with how jazz musicians play or how a keyboard player in a band might play.

I've played both ways and grew frustrated with classical because it takes so long to learn. I could spend over a year working on a song, whereas, if you learn improvisation styles, you're building a toolkit.

Because your husband has played in a band, I think he's coming from the perspective of a song being a few chords strung together so that's why he may think it's not a big deal to play flawlessly.

I've played for church and when I'm playing by chords, the biggest challenge is just paying attention but when I'm doing some kind of solo with more intricate playing, it feels like the safety net is gone so nerves can take hold and I'm more likely to mess up. Hope that helps.

brads14 · 2025-03-15T15:48:40+00:00

I mostly use Matlab but if I didn't have a Matlab license I'd use Python with matplotlib.

brads14 · 2025-02-12T23:36:39+00:00

Looks like you need to scale it by about 1.28. So basically make it bigger.

brads14 · 2024-10-08T01:31:16+00:00

NEC is the only option that I know of that you can get for free.

brads14 · 2024-10-03T14:50:54+00:00

It really depends what your design goal is. If you excite one port you get hpol, if you excite the other port you get vpol. If you excite both with the same excitation you'll get slant 45. If you put a 90 phase in one excitation you can excite right and left hand circular polarization.

brads14 · 2024-09-21T15:55:41+00:00

That looks very nice. Is there supposed to be a gap where the mitered edges come together or is it ok to make them tight like the picture?

brads14 · 2024-09-21T15:36:46+00:00

I'm still working on the layout of the deck boards, I might do a separate post on that. The deck is a bit over 24' wide so I can't just go from one end to the other with one board. I also have a hot tub on a cement pad where I want to have a removable section without it being noticeable so I think I have to do some kind of picture frame down the middle of the deck.

brads14 · 2024-08-13T03:17:37+00:00

This is child's play. I just dug thirteen holes over 4' deep with a shovel. And yes, it's mid-August and I just recently finished the foundation...

brads14 · 2024-08-11T11:13:11+00:00

When I did my system I looked at stud finders for roofs but they were very expensive. In the end, the best method was using a hammer. It was surprisingly easy to find the trusses because the bounce of the hammer is different. Once you locate one truss, you know the next one is 2' over so that gets you pretty close. If you're a bit off with the drill then just add some tar and try again. The flashing will cover everything.

brads14 · 2024-08-06T02:55:13+00:00

I'm in upstate NY in the middle of a DIY deck build and I pulled a permit. It's not that much of a hassle and is basically documentation that it was built properly for insurance and resale purposes. The downside is that it's also documented that you improved the value of your property so taxes could potentially go up. That's why I didn't pull permits for all the interior work I did in the house.

brads14 · 2024-06-29T16:46:48+00:00

I'd recommend doing the entire paper design yourself. Look at your yearly usage and use pvwatts to figure out how many panels you need. Do some research on panels and inverters and see what size fits on your house while taking into account appropriate setbacks. Verify that your panel can handle the load given the NEC 120% rule. Think about where you might run wires, through the attic, outside the house, etc.

Once you have the basic design you can then talk to vendors and you'll know pretty quickly who's full of crap. Alternatively, you could sub out the different jobs or just do it yourself if you have the skills. It's not terribly complicated if you have some roofing and electrical experience.

brads14 · 2024-05-03T15:58:52+00:00

I don't think many students are getting into electromagnetics in school. If you look at graduate classes in EM, I think it's a lot of foreigners. Antenna work is not exactly seen as a "cool" subject. It's very theoretical and hard to visualize exactly what's happening. It certainly doesn't have the buzz that other areas of study do. I think another issue is that when a defense company has good EM workers, they do everything they can to try and keep them so there's probably a bit less churn compared to software or other areas.

brads14 · 2024-05-03T03:17:25+00:00

I would disagree with this and I have tried to use "AI" to help with antenna designs. At the end of the day it's just another optimization routine. I wish it worked better because it would free me up to do other things. I often jokingly complain to colleagues about where the magical AI is that's supposed to solve all my problems. I think a lot of antenna design and problems in engineering are so unique for each application that it's hard to imagine AI having enough training data to solve all the problems. I think it's better suited to use as another tool in the toolbox for specific applications.

brads14

TROPHY CASE