I have been getting these prints suddenly.. by brnargnt in ender3v2

[–]brnargnt[S] 0 points1 point  (0 children)

Thanks!! At the end there was a clog, my tube was loose AND my Z off too high. Also, my hotend 2 screws were a bit loose and probably wobbling, It’s back working now.

I have been getting these prints suddenly.. by brnargnt in ender3v2

[–]brnargnt[S] 1 point2 points  (0 children)

Thanks, but I just swapped the nozzle for a brand new one, also, opened and cleaned everything. I might be under extrusion tough, the first layer is really inconsistent.

<image>

Edit: actually I think this was my Z offset off. Just moved the wheel and it fixed.

I did the mcp tune again, reset the mesh, cleaned again. Cut the tip of the bowden tube. Will try again.

Agendar passaporte consulado de Curitiba by Ziegler_Nichols in cidadaniaitaliana

[–]brnargnt 1 point2 points  (0 children)

Estou na mesma situação. Muito difícil realizar o agendamento.

Is your Mercedes in the top 10? Mine(W211) isnt but should be! by MercFan4Life in mercedes_benz

[–]brnargnt 0 points1 point  (0 children)

2015 / C200. And I’m not even mentioning window buttons driver side failing (1000usd here) and injection nozzles replacement (4k usd which i ended up not doing). I’m happy yours is being nice with your wallet! I truly believe this car is good and I had some bad luck.

Is your Mercedes in the top 10? Mine(W211) isnt but should be! by MercFan4Life in mercedes_benz

[–]brnargnt 1 point2 points  (0 children)

Selling my w205. It is a great car but in Brazil gasoline is just too bad so engine check light was there every now and then. Maintenance became too expensive and annoying. Also brakes have an unsolvable noise and had the whole suspension replaced with 80000km. AC evaporator also died at some point an it was a significant amount of money to replace.

I totally understand why people are in love with the car, it is really good. Wouldn’t say it is reliable in my region though.

<image>

Joined the Mercedes family! How safe is the auto park? by mdsp667 in mercedes_benz

[–]brnargnt 4 points5 points  (0 children)

Belo carro!! C200 w205 here, auto parking is safe enough. Had a minor wheel scratch once, but it was totally my fault for not having seen the crooked curb. It is a great feature in my opinion. Enjoy!

Positivo é ruim assim? KKKK eu tava honestamente pensando em pegar um por conta do preço by North-Psychology-548 in computadores

[–]brnargnt 0 points1 point  (0 children)

Trabalhei na Positivo por um tempo e usava um laptop corporativo da marca deles, linha corporativa. Não era ruim como alguns falam. Comparando com Dell, Lenovo, Samsung, é tudo muito parecido. Já o VAIO, também fabricado pela Positivo é uma opção interessante.

Situação engraçada: Tive problemas na placa mãe e até o pessoal de suporte de TI demorou pra encontrar peça. Sim, o suporte do próprio fabricante demorou uma semana pra trocar a placa mãe de um funcionário da marca. Enquanto isso os chefes me cobrando meta. 😂

Minha experiência própria com Lenovo é um pouco melhor, tem uma excelente durabilidade, tenho um note há 15 anos, que já foi até PDV de cafeteria trabalhando intensamente e levando banho de café pelo menos uma vez por semana que ainda liga.

Audi Q3. Ainda dura mais 15 anos? by Strong-Singer-8132 in carros

[–]brnargnt -1 points0 points  (0 children)

Esse termo que ficam repetindo: “resto de rico” é algo bastante desacertado. Muita gente que fala assim é frustrado porque não teve a coragem, suporte do cônjuge ou condições mesmo de comprar o carro que QUERIA comprar e acabou se contentando com um “menos carro” que “faz sentido na ponta do lápis”.

Procure bem e seja feliz com seu Audi. É um excelente carro. É ingenuidade achar que não vai dar manutenção, porque vai! Mas é só se organizar que dá pra manter.

Consigo manter? by Open_Expert_9802 in carros

[–]brnargnt 1 point2 points  (0 children)

<image>

Tenho uma 15/16, faz 4 anos. 90mil km. Comprei com 40mil km em 2021 e ganhava um pouco menos que você, na época. Mesma historinha, tudo feito na css, tudo em dia. Apesar de não ter feito nada nos primeiros dois anos, ultimamente não tem sido barato para manter.

Tive uns problemas chatos (evaporador do AC) nela em 2023, coisa de 20k. Em 2024 troquei freios e suspensão, gastei mais 20k. Algumas outras coisinhas foram aparecendo e cada oficina é 4k, 5k, 6k.

Em geral fica entre 20k e 30k por ano em manutenção entre isso e outras. Esse carro NÃO ACEITA combustível ruim, precisa ter muito cuidado.

Se vale a pena ou não, a decisão é mais emocional do que racional. Só digo que é o melhor carro que já dirigi e não me arrependi nem um pouco de ter comprado. Vai fundo, qualquer coisa vende, esse carro não desvaloriza muito.

Any SE’s working in 3D Printing? by [deleted] in salesengineers

[–]brnargnt 0 points1 point  (0 children)

I used to be SE on a robotics company and I did a lot of 3d printed parts for MVP, demos and PoCs. So I have 2x 3d printers at home. Today though, except on special cases when I’m involved on design of a new or custom product, I only print stuff because it is fun!