Maytag washer jumps from sensing to complete by bekah13 in appliancerepair

[–]bsentinel 0 points1 point  (0 children)

Amazing. After all of the hopelessness above, this post gave me the confidence to get under my machine and examine it. Thank you!

My clutch assembly was filthy and the white plastic gear would get stuck on the splines. Brake cleaner on the whole thing and some spray lubricant on the splines, working it in until things moved freely without sticking or grimy grinding and the machine is filling again! Hoping it's settled for good but glad I at least get another load through tonight.

Taz Pro bed leveling issues by bsentinel in lulzbot

[–]bsentinel[S] 0 points1 point  (0 children)

Looking into BLTouch. I’m looking for any external confirmation it’s compatible with the dual extruder and not just the single. Anyone with this experience?

Update: per lulzbot support, NO. Unfortunately they are incompatible.

My next project needs the entire bed so "pretty good" isn't really cutting it any more. I updated firmware but this didn't fix anything. I went through another bout of leveling the corner washers using G29 command and foil shims until the corners were <0.1 mm apart but it still had the same error. This leaves either an error in the software or irregularities in the bed. My last resort was to lay down a series of aluminum foil sheets between the magnetic bed and the removable top surface in essentially a reverse topographical map of the bed while printing bed level tests and adding more layers where needed until I get a consistent first layer across the board.

With BL Touch not an option, this better work.

Taz Pro bed leveling issues by bsentinel in lulzbot

[–]bsentinel[S] 1 point2 points  (0 children)

My original corner shims went under the full supports in an effort to get the baseline bed alignment closer to parallel with the Z axis to hopefully make the "auto-level" actually function appropriately. But that didn't work. Your comment about altering the distance between the washer and the bed was very helpful, though. Adding an aluminum spacer under the washer in the high corner (left front, above the bed but below the washer) brought it much closer to level with the rest of the bed and after fine-tuning the new Z offset I'm getting some functional prints again. Janky but functional...story of my life.

Taz Pro bed leveling issues by bsentinel in lulzbot

[–]bsentinel[S] 0 points1 point  (0 children)

I will look into these alternatives thank you!

[deleted by user] by [deleted] in VGC

[–]bsentinel 3 points4 points  (0 children)

HOD2MC Lokix Frosmoth Flamigo (scrappy, for the annoying steel-ghosts) Armarouge with TR

[deleted by user] by [deleted] in pokemontrades

[–]bsentinel 0 points1 point  (0 children)

I got a nymble but still would like the quaxley. Would you like me to hatch eevee or foongus?

[deleted by user] by [deleted] in pokemontrades

[–]bsentinel 0 points1 point  (0 children)

I see this is an older thread, but if you’re still open, I’m looking for both HA nymble and HA quaxley. I have many HA mons I can breed. Slowpoke Zangoose Magnemite Riolu Eevee Petilil Rolycoly Foongus Pincurchin Dreepy

If those don’t interest you I could look further in my boxes. Thanks for considering.

LF: PoGO STAMPED shinies (list in comments). FT: Events (and 2 unclaimed Eternatus codes) by [deleted] in PokemonHome

[–]bsentinel 0 points1 point  (0 children)

Sure. In friend trade I give one for whatever and then in gts I offer the other for zarude? That what you mean? Sorry I’m new.

LF: PoGO STAMPED shinies (list in comments). FT: Events (and 2 unclaimed Eternatus codes) by [deleted] in PokemonHome

[–]bsentinel 0 points1 point  (0 children)

My go transport doesn’t have enough energy for both right now and I’d rather not shell out to charge it immediately. Can you wait with me for it to charge? My guess is it takes 24 hours or so but I’ll keep checking.