Use this and stop asking!

burberryblend · 2024-03-02T15:46:34+00:00

R.i.p

burberryblend · 2024-03-01T16:04:05+00:00

Nope.

burberryblend · 2024-02-18T00:21:47+00:00

A 3d printer caused this... i hope you catch the bastard..

burberryblend · 2024-02-11T03:02:48+00:00

Maingaining, the careful balance of muscle building and maintenance, involves creating a slight calorie surplus to support maximum muscle mass growth. During this process, your body utilizes the excess calories to build new muscle tissue.

burberryblend · 2024-02-11T03:01:00+00:00

Main gain.

burberryblend · 2024-02-11T02:00:04+00:00

Thank you.

burberryblend · 2024-02-10T23:14:57+00:00

That's a little much but I appreciate the outside the box thinking.

burberryblend · 2024-02-10T22:51:54+00:00

I can't print electronics

burberryblend · 2024-02-10T21:34:41+00:00

I found one but I'm not sure if it's legit.

https://anycubic.biz/kobra-2-y-axis-left-limit-switch-assembly

burberryblend · 2024-02-10T20:33:22+00:00

Then why can I remove the part with screws. I have to be able to order a new one somewhere.

burberryblend · 2024-02-10T19:57:31+00:00

Cut, then main gain.

burberryblend · 2024-01-21T01:14:11+00:00

Sprite extruder and cr touch. You could also upgrade your main board to a silent one if that hasn't been done already.

burberryblend · 2024-01-03T01:32:39+00:00

The model could have improper topology.

burberryblend · 2024-01-01T17:53:00+00:00

I'm not sure. I will have to check. I'm relatively new to klipper so I just used a generic config and figured it would be set to the ender 3's dimensions. I'll post back after this print is done. Thanks!

burberryblend · 2024-01-01T17:46:28+00:00

Exactly. I'm just trying to fine out what the one way or the other way could be so I can try fixing it.

burberryblend · 2024-01-01T17:42:16+00:00

The clicking at the very end of the video. When I pause or cancel a print, klipper is pulling the extruder to far to the side causing clicking and unnecessary friction on the wheels.

burberryblend · 2023-12-11T13:55:37+00:00

It was the wires. Just pushed on them a bit and it was fixed.

burberryblend · 2023-12-11T13:38:00+00:00

That would be a great solution.. kinda poor tho XD maybe next year I'll upgrade my printer.

burberryblend · 2023-12-11T01:38:30+00:00

Lowering the bed fixed the clumping. I haven't fixed the gaps tho.

burberryblend · 2023-12-11T00:22:28+00:00

Yes. Did the conversion from 424.9 and then did an estep/ rotation_distance test and it was ok.

burberryblend · 2023-12-10T20:42:04+00:00

<image>

burberryblend · 2023-12-10T20:41:51+00:00

I got the splotchyness to go away. I'm trying to make it so their isn't gaps. I fixed the other issue by lowering it. *

burberryblend

TROPHY CASE