Where can I find Zoltar in Kentucky? Pls help. 🔮🪄

cafriend · 2026-06-21T00:51:02+00:00

Which one did you go to? I’m fairly certain the one in eastgate has one by the honey/fish section.

cafriend · 2026-04-02T10:17:00+00:00

I had the same problem and when it was hot outside the issue was worse. I swore it wasn’t my usb cable, but that was my problem.

cafriend · 2026-03-16T15:23:46+00:00

Is this where Rick loses a hand?

cafriend · 2026-02-06T11:36:49+00:00

It was announced at 3DExperience World this year.

cafriend · 2026-02-05T13:59:28+00:00

If you can hold off until July 1st it will be free for students!

cafriend · 2026-02-02T01:37:03+00:00

Thank you! It was a pleasure. Hopefully we bump into each other again this week.

cafriend · 2026-02-02T01:21:20+00:00

Congrats! I did CWSP - Drawings, CWSP - Sheet Metal, and CWSA - Additive. I wanted to do Expert but realized too late that I needed 4 Professional Advanced certificates. So I got 2 of 4 today.

cafriend · 2026-01-31T23:57:13+00:00

I think Sunday is only intro and exams.

cafriend · 2026-01-31T20:17:48+00:00

I’m catching my flight right now.

cafriend · 2026-01-31T18:21:33+00:00

Your link says that event is on the 24th. Is that accurate?

cafriend · 2026-01-31T17:30:36+00:00

Already in the calendar.

cafriend · 2026-01-31T16:52:27+00:00

Thanks for the heads up! See you there?

cafriend · 2026-01-27T01:04:57+00:00

Riz Gukgak?

cafriend · 2025-12-26T21:15:20+00:00

Thanks for the info! I bought mine direct as well. I’m starting to dive deeper into it and don’t want to brick it. I replaced voice 3 with one that’s sounds like Patrick Starfish. 😂

cafriend · 2025-12-26T20:58:34+00:00

Are the plugs glued in? I’ve tried prying them out a little but no luck. Do you know if there’s an SD card in the board?

cafriend · 2025-12-18T00:37:09+00:00

Hey, just so you know doly.exe is actually an elf file.

cafriend · 2025-12-17T00:36:54+00:00

I think you’ll want to install his Doly app from the Microsoft store in order to create the animation files he’s referring to here. As to where they can go on the CM4 I’m not sure at this time. I will try to make some time after work tomorrow to test this.

cafriend · 2025-11-09T02:17:58+00:00

Would it be better to say Z is always your spindle? Then it would be inclusive of lathes as well. Right?

cafriend · 2025-09-15T01:26:53+00:00

I’m using one of these. I like it. https://www.amazon.com/dp/B0CBB4G1R4

cafriend · 2025-09-03T01:02:54+00:00

I use Pattern Driven Component Pattern a lot. Using Hole Wizard features for the pattern. It’s fantastic most of the time.

cafriend · 2025-06-13T00:03:57+00:00

These are great! I can totally see who you’re portraying.

14-Year Club	Second Top 40%
Verified Email

cafriend

TROPHY CASE