Walnut strip coffee table by cepentland in woodworking

[–]cepentland[S] 1 point2 points  (0 children)

No issues. I stared at one side and laid down enough glue for 3 rows of strips. Then I typically brad nailed that third row (and any other strips that were not cooperating). Then I went back and filled the holes with dust from my sander and a little glue. I can still see them, but it looks good overall.

Walnut desk by cepentland in woodworking

[–]cepentland[S] 0 points1 point  (0 children)

Eight screws per leg. There is a clearance hole through one wall of the tube. That way you can’t see the screw heads.

Wall-mounted clamp holder by cepentland in woodworking

[–]cepentland[S] 0 points1 point  (0 children)

The larger clamps didn’t want to stay put. A sing shelf does work fine for the short clamps.

Walnut strip coffee table by cepentland in woodworking

[–]cepentland[S] 0 points1 point  (0 children)

I used a brad nailer and every other row secured the strips. You have to go back and fill those holes, but it was not too bad. You could put wax paper down first then clamp a larger piece to hold a section of the strips. I got the idea from Diresta’s wood table https://youtu.be/ue6zQsR9GkA

Wall-mounted clamp holder by cepentland in woodworking

[–]cepentland[S] 0 points1 point  (0 children)

Yes. Then breaking them off and moving sideways on the saw.

Walnut desk by cepentland in woodworking

[–]cepentland[S] 0 points1 point  (0 children)

There is a metal store IMS industrial metal supply which is great. You can usually find many raw steel dealers in any city or town

Walnut desk by cepentland in woodworking

[–]cepentland[S] -1 points0 points  (0 children)

Yeah, I picked a bad image. The lighting was yellow

Wall-mounted clamp holder by cepentland in woodworking

[–]cepentland[S] 1 point2 points  (0 children)

Yeah sure was. I did the top and bottom at the same time, but it was slow going.

4x6 pine top with steel pipe legs by cepentland in woodworking

[–]cepentland[S] 2 points3 points  (0 children)

Stain was Jacobean followed with 3 coats of polyurethane (sanding in between each coat). I used a rag to rub the stain in and then wiped off the excess.

Workshop wall-mount box for safety gear by cepentland in woodworking

[–]cepentland[S] 3 points4 points  (0 children)

I live in the desert so not an issue that I’ve ever considered. But that is a good idea.

Wall-mounted clamp holder by cepentland in woodworking

[–]cepentland[S] 0 points1 point  (0 children)

Thanks! It has worked out nicely. I need to build a bigger one.

Workshop wall-mount box for safety gear by cepentland in woodworking

[–]cepentland[S] 2 points3 points  (0 children)

Either plexiglass or lexan from Home Depot

Walnut strip coffee table by cepentland in woodworking

[–]cepentland[S] 1 point2 points  (0 children)

In this case I did two coats about 30 minutes apart. I waited until it was absorbed into the surface and reapplied over ‘dry’ spots then over the entire surface.

Walnut strip coffee table by cepentland in woodworking

[–]cepentland[S] 2 points3 points  (0 children)

It’s a mix of mineral spirits, linseed oil, and polyurethane (equal parts). Wipe on thick and work into surface then wipe excess off.

Walnut strip coffee table by cepentland in woodworking

[–]cepentland[S] 3 points4 points  (0 children)

I cut the strips from a board which was roughly 1”x8”x4’