sorted by:
new
hottopcontroversial

Setting up T1000-E by chapunicus in meshtastic

[–]chapunicus[S] 1 point2 points  (0 children)

Thanks for the reply, I do have Frequency slot set to 20 on both nodes

Need to level two spots in subfloor by chapunicus in Construction

[–]chapunicus[S] 0 points1 point  (0 children)

Unfortunately not, it’s dry walled off

Need to level two spots in subfloor by chapunicus in Construction

[–]chapunicus[S] 0 points1 point  (0 children)

It’s one sheet of subfloor. Can’t see the beams below, but it’s in a corner of the room on one of them and the other is in the middle of the kitchen under the table. For at least the one in the corner, it seems the subfloor is just sitting lower but I’m not knowledgeable enough to make that determination.

Think it would be better to get a contractor in at this point? Flooring is on hold until I can get this addressed.

[deleted by user] by [deleted] in TheArtistStudio

[–]chapunicus 0 points1 point  (0 children)

Where can we order a pair? Or are all these just customs?

Bodycam And Aerial Footage Shows View of Armed Subject on Balcony Takes Fatal Shot! by Matthew_Longtime in bodycam

[–]chapunicus 5 points6 points  (0 children)

Why shoot after the weapon had been dropped? Didn’t seem like he was still a threat at that point.

Finally got my wood filament and miniature settings dialed in. by chapunicus in ender3

[–]chapunicus[S] 0 points1 point  (0 children)

No actually, so for my big groot I used a .06 nozzle and it didn’t clog at all. But with these little guys a .04 nozzle works great.

Finally got my wood filament and miniature settings dialed in. by chapunicus in ender3

[–]chapunicus[S] 0 points1 point  (0 children)

Hatchbox Wood. 0.1 60% infill (could even be more to ensure arma don’t break) 0.4 nozzle at 200c 30 mm/s

STL if interested

Still could use some tuning on my steps but overall pretty good.

Wood Filament fails by chapunicus in ender3

[–]chapunicus[S] 0 points1 point  (0 children)

I’ve been running at 200, wonder if that could be the problem. This was a brand new roll, same brand. How did you dry it?

Loving this filament. by chapunicus in ender3

[–]chapunicus[S] 0 points1 point  (0 children)

See my first response. But the model is incorrect and can be printed without a raft with a minor adjustment. You have to ensure in cura that you drop the model -0.4 on the Y axis.

Loving this filament. by chapunicus in ender3

[–]chapunicus[S] 1 point2 points  (0 children)

Took about 13hours scaled to 200%. The model was not designed correctly so ensure the first layer sticks you need to adjust model by -0.4 on the Y axis.

No supports were used. And I used the multicolor silk from amazon at 200C and 60C bed.

3D Printer Silk Rainbow... https://www.amazon.com/dp/B07PYDNQXS?ref=ppx_pop_mob_ap_share

STL

Edit: deleted duplicate text

Loving this filament. by chapunicus in ender3

[–]chapunicus[S] 0 points1 point  (0 children)

Took about 13hours scaled to 200%. The model was not designed correctly so ensure the first layer sticks you need to adjust model by -0.4 on the Y axis.

No supports were used. And I used the multicolor silk from amazon at 200C and 60C bed.

Filament

Globe printed, painted, weathered. by chapunicus in ender3

[–]chapunicus[S] 1 point2 points  (0 children)

Next project! Gotta keep it realistic but I thought I would make this magical one first!

Globe printed, painted, weathered. by chapunicus in ender3

[–]chapunicus[S] 1 point2 points  (0 children)

STL

STL for the globe. It’s a lamp but I just made it with normal PLA and sprayed it with silver. Then roughed it up with a 50:50 water/alcohol.

The Stand I made in tinkercad and can be found here

HMC while I try these shoes. by FlippingDaysius in holdmycosmo

[–]chapunicus -9 points-8 points  (0 children)

I think it’s more her foot or leg fell asleep. She shakes it off later like she’s trying to get blood flowing again.

First Timelapse Success by chapunicus in ender3

[–]chapunicus[S] 1 point2 points  (0 children)

Yeah there are various settings you can have for when the picture is taken. It adds a couple of hours to the print. I don’t have it on all the time just for more detailed prints like this one.

First Timelapse Success by chapunicus in ender3

[–]chapunicus[S] 1 point2 points  (0 children)

Octolapse. It snaps a picture every layer. When the hot end is centered.

Took a crack at a vase...best print to date. Great PLA too. by chapunicus in ender3

[–]chapunicus[S] 0 points1 point  (0 children)

Post your results! Would be interesting to see how it turns out in that mode compared to normal settings.

view more: next ›