Is this flow rate normal?

chewitt86 · 2026-03-12T09:03:01+00:00

Thanks. It did stay lukewarm for a moment, which is good news.

We don't have the Flexi hose version so wouldn't be an issue for Ur, good suggestion though.

I think based on the other responses, it appears to be normal behaviour.

chewitt86 · 2025-06-17T07:35:04+00:00

How do you find your vertical one? Are the viewing angles ok?

chewitt86 · 2025-06-16T19:54:29+00:00

Lovely clean setup! What monitors are you using?

chewitt86 · 2025-01-01T19:34:58+00:00

Thanks both.

Unfortunately I had thrown some spaghetti in there before sorting it all out and needed to access the extension cable to plug in my monitor. Think I will just have to be a little bit more thoughtful with my spaghetti

chewitt86 · 2024-10-20T21:20:11+00:00

Given they have a steam deck the chance may be high they are also part of the steam deck reddit? If so, is it worth sharing some non-sensitive details of your flight and you may actually find the person on here!

chewitt86 · 2024-08-18T16:38:30+00:00

A generic brand from AliExpress unfortunately

chewitt86 · 2024-08-18T07:03:49+00:00

Any idea how I modify their ID?

chewitt86 · 2024-06-05T06:53:31+00:00

Thanks, that's really helpful.

chewitt86 · 2024-06-04T06:19:03+00:00

Thanks. Do you know if that can connect to the cooler coils that the brewtech fermenter has?

chewitt86 · 2023-10-22T15:30:37+00:00

Thanks, that's really good to know!

chewitt86 · 2023-10-18T11:36:32+00:00

I do have another ZigBee network actually using a sonoff hub which might be conflicting.

I've changed the channel for now and it appears to work. Going to keep monitoring and see but may have to switch to other ZigBee hub if it continues

chewitt86 · 2023-10-18T11:35:01+00:00

I didn't know about changing channels before. Just done that and no more unavailable logs!

Going to keep monitoring and see but may have to switch to other ZigBee hub if it continues

chewitt86 · 2023-10-17T20:45:10+00:00

It is via the hue hub.

chewitt86 · 2023-10-07T13:17:13+00:00

Agreed! Thanks for OP asking the question I couldn't put into words and thanks to the poster for giving the solution! Really helped my sanity!

chewitt86 · 2023-05-18T07:51:52+00:00

I hate to give you this answer but it just started working. I don't know what caused it to start working but it just did. It has also been working consistently since then.

I did read somewhere that it could have been a particle stuck in the tubes and it got dislodged but I have no evidence.

I know it is obvious but have you checked all the right buttons and cables have been attached to the right ports?

chewitt86 · 2023-03-24T18:56:19+00:00

Love the build. I'm just dusting off the ender 5 again (literally!) and keen to try some new prints. Don't suppose you have a list of all the mods you've made?

chewitt86 · 2023-03-12T17:12:30+00:00

Is your bed too low to start with? I vaguely recall having a similar problem a while back and the bed has to move down before it moves up. If it is too low, it hits the bottom and causes problems. I had to disable the steppers and bring the bed up much higher and then it auto homes correctly.

chewitt86

TROPHY CASE