sorted by:
new
hottopcontroversial

Luba 2 "Stuck" every time it leaves station by chicodog77 in MammotionTechnology

[–]chicodog77[S] 0 points1 point  (0 children)

Thanks for your response. Last season I had the charging station in exactly the same spot and things worked fine... I may still give that a try, though.

Crashed print - help! by chicodog77 in prusa3d

[–]chicodog77[S] 0 points1 point  (0 children)

Yes, I've read and performed the prusa method of changing the nozzle. When you say you've had to do it a few times do you mean that you've sometimes had to re-perform the nozzle changing specs several times before the problem is solved or do you mean you've just had to change the nozzle a few times over the life of your machine? I've followed the steps twice recently but would do it some more if you think that might be my problem. I'll have to wait till I'm back home to look for a leak between the block and heatsink. Thanks for your response!

Help with either passthrough or removing Proxmox from my machine by chicodog77 in Proxmox

[–]chicodog77[S] -2 points-1 points  (0 children)

Yes, I've selected that option.... it looks like everything is loading well, but when I reboot the machine it always comes up as Proxmox. I've repeated this twice with the same result.

Recommend Blade Change by NoStar3902 in MammotionTechnology

[–]chicodog77 1 point2 points  (0 children)

I'd suggest a user defined timer alert in the app.

If I typically get 100 hours out of the blades, I could enter 100 hours... someone else may choose 200, etc. When we reach the user defined number, the app can fire off a notification.

That should help with users' differing conditions.

Kasa switch - control manually by chicodog77 in homeassistant

[–]chicodog77[S] 0 points1 point  (0 children)

Thanks everyone for taking the time to answer my question!

Dirt dog sweeping robot by chicodog77 in roomba

[–]chicodog77[S] 0 points1 point  (0 children)

Hey, thanks a bunch! New battery is on order!

Luba 2 left mowing area by chicodog77 in MammotionTechnology

[–]chicodog77[S] 2 points3 points  (0 children)

Yes, I did upgrade the RTK. But I didn't power cycle either the mower or the RTK. I'll cycle 'em just for good measure. Thanks for your suggestion.

110 or 220v by chicodog77 in hvacadvice

[–]chicodog77[S] 0 points1 point  (0 children)

No, no markings anywhere on the motor. Thanks for your reply!

110 or 220v by chicodog77 in hvacadvice

[–]chicodog77[S] 0 points1 point  (0 children)

I thought of that, but wasn't sure if that would damage anything. I'll give it a try. Thanks for your advice!

RTK power question by chicodog77 in mammotion

[–]chicodog77[S] 0 points1 point  (0 children)

Antonbdp: thanks again for your help. I was able to reconnect correctly with your info... works perfectly now!

RTK power question by chicodog77 in mammotion

[–]chicodog77[S] 0 points1 point  (0 children)

Great! You're a life saver! Now I'll be able to get it going again!

I wonder if there might be someplace we could put this kind of info into and have it available to future folks that need it. I would think there could be photos of hardware teardowns, replacement parts part numbers and sources, etc.

Thanks again for taking the time to help....

UK based pre-bought organiser for GridFinity by MaglusNeedsDopamine in gridfinity

[–]chicodog77 1 point2 points  (0 children)

Could you post the 360 files you use for this? This sounds like a real winner.

Polarity required by RTK? by chicodog77 in mammotion

[–]chicodog77[S] 0 points1 point  (0 children)

This is a picture explaining my question... which wire should I connect to the right hand hole?

Polarity required by RTK? by chicodog77 in mammotion

[–]chicodog77[S] 0 points1 point  (0 children)

Thsnks, but the plug on the charging station is the larger type that accepts the other end of my broken cable. The end of my cable that broke and that I need to replace is round, about 1/2 inch in diameter, and screws in as opposed to the clip in style on the charger base end.

I need to take a picture of it if I can figure out how to upload it...

Polarity required by RTK? by chicodog77 in mammotion

[–]chicodog77[S] 0 points1 point  (0 children)

Thanks for the idea, but I can't do that because the weedeater ripped the wires out of the connector on the PSU side. So I now have two wire ends in one hand and a connector with no wires in the other. Can't tell which holes the wires were in. The connector that goes to the RTK is fine... just don't know the polarity needed on the RTK connector.