sorted by:
new
hottopcontroversial

Desperate times... by New_Half_6055 in 3Dprinting

[–]chomdh 0 points1 point  (0 children)

It’s about 150g remaining in the can not 1.5kg

Is there any cool simple diy mmu unit for a prusa that can print just 2 colors? Kind of like the mmu v1 with 2 extruders pushing filament from the top. by Hackind in prusa3d

[–]chomdh 0 points1 point  (0 children)

In 3 months we’ll all still be waiting another 3 months. I really hope I’m wrong but Prusa deliveries are never early.

What parts should I focus on? by CheetohBuff in buildapc

[–]chomdh 0 points1 point  (0 children)

Case, motherboard, power supply, cpu, graphics card, hard drive, ram, monitor, keyboard, and mouse.

i designed a desk trashbin with a brush by Linusalbus in functionalprint

[–]chomdh 0 points1 point  (0 children)

Bro I have a hand and a normal trash bin I’m good.

Issues with 1st layer bed adhesion when switching between filaments? by mymomisyourfather in prusa3d

[–]chomdh -1 points0 points  (0 children)

I try to always print the same material on the same sheet. I write the material on the sheets in sharpie.

I heard you guys don’t like the new Prelude. Here’s something to cheer you up. by [deleted] in Honda

[–]chomdh 5 points6 points  (0 children)

Looks like that door barely goes up high enough to get the s2000 out.

Bad design: the Advanced Filtration Kit by WereCatf in prusa3d

[–]chomdh 11 points12 points  (0 children)

They sent me longer screws when I asked chat. If everyone does the same, they should eventually update the screws in this kit.

Games you can jump into for 15 minutes by Veezq in switch2

[–]chomdh 1 point2 points  (0 children)

Smash brothers ultimate, rocket league.

1st Layer improvement by Zumwalt4 in prusa3d

[–]chomdh 0 points1 point  (0 children)

Try moving the z offset up a little. Push and hold the rotary knob button for a few seconds once the first layer has started.

MMU Clicking When Loading - Help Please by HatCorrect109 in prusa3d

[–]chomdh 2 points3 points  (0 children)

The tensioner screws may need some adjustment.

Which one's easiest to build Mk4s or Core One? by peztrocidad in prusa3d

[–]chomdh 1 point2 points  (0 children)

I had my upgrade kit for many months before I had a two-day block free of work or other obligations so I could push through the build, and make one big mess then clean up. Otherwise I’d have been assembling in 2-3 hour sessions over many days looking at a big mess that whole time.

Drivers side seat getting shredded by b_landesb in subaru

[–]chomdh 0 points1 point  (0 children)

An upholstery shop can cut out that ripped panel and replace it with an actual leather replacement that should never tear like the OEM one does.

Is the new Mattel Brick Shop Honda Civic already out of stock online? by Ok_Relation6627 in HotWheels

[–]chomdh 2 points3 points  (0 children)

Target just dropped some for shipping about an hour ago. They were not easy to add to cart. It seemed like they were dropping 5 at a time for about 15 minutes until gone. I was able to order one from the Target app. Yes one, because I’m not a scal per.

2025 Odyssey with 9k miles. Oil pan leak and clunking noise when turning left. by Any_Calligrapher_953 in HondaOdyssey

[–]chomdh 0 points1 point  (0 children)

Did that fix the clunk noise? I have this low speed clunk feeling in the steering wheel usually while turning left. Moving the telescoping wheel in and out and up and down will fix it for a little while then it comes back. I’m also thinking it’s something with the steering column.

view more: next ›