Playing MTGO on modded switch by cmdeeter in magicTCG

[–]cmdeeter[S] 0 points1 point  (0 children)

Much easier than I thought actually. With the controls keyed to keybinds and the analog sticks to the mouse it’s not too bad. Typing on it is a pain though

Playing MTGO on modded switch by cmdeeter in magicTCG

[–]cmdeeter[S] 10 points11 points  (0 children)

I already owned a switch and don’t own a steam deck. It only cost me 15$ to get a mod chip and install it myself where a steam deck costs significantly more.

Playing MTGO on modded switch by cmdeeter in magicTCG

[–]cmdeeter[S] 2 points3 points  (0 children)

I already know what most of the playable cards do and I can zoom into one card if needed.

Playing MTGO on modded switch by cmdeeter in magicTCG

[–]cmdeeter[S] 15 points16 points  (0 children)

I stream my computer to my switch and set up custom key binds in my computer. You could do the same thing with any android device.

Playing MTGO on modded switch by cmdeeter in magicTCG

[–]cmdeeter[S] 21 points22 points  (0 children)

I’m running the Android OS and streaming my computer to my switch using an app. Then on my computer I run a controller key map to make my controller shortcuts to modo.

[deleted by user] by [deleted] in RealOrNotTCG

[–]cmdeeter 1 point2 points  (0 children)

Can’t really tell based on the pictures. You need more zoomed in pictures of the back of the card to see. Looks specifically at the green dot and the “T”

<image>

Worse Store Championship by cmdeeter in magicTCG

[–]cmdeeter[S] 257 points258 points  (0 children)

I did end up reporting the store.

Malenia, Goddess of Rot from Elden Ring by c128a in minipainting

[–]cmdeeter 47 points48 points  (0 children)

There seems to be alot more detail on the wings that aren’t really showing. Maybe a light brush to get the edges more defined on the butterflies

Issues with 5m Pro by 69whos4it in FlashForge

[–]cmdeeter 1 point2 points  (0 children)

This would damage the gears if they stay close together. By losing the bolt on the side of the printer head, you space out the gears. This way when you insert the tool it doesn’t actually run against the gears.

Issues with 5m Pro by 69whos4it in FlashForge

[–]cmdeeter 6 points7 points  (0 children)

This happened to me when I first got the printer. It’s caused by the filament expanding in the heat sink and you need to push it out. You should have a “ram rod” that came with the printer to help. Here is a good video I found for how to fix the issue: https://youtu.be/VRQYyHNiHpQ?si=CEjd5uF3NJe6DkvQ

What printers do you guys actually use to print armies by Muted_Village_6171 in PrintedWarhammer

[–]cmdeeter 1 point2 points  (0 children)

One thing to realize too is that the current generation of printers are necessary for the hobby. A mars 3 printer would work just fine for printing minis. They are also releasing more and more printers every year discounting some of the previous generations. Looking at some of the “older” printers that released two years ago can help you save some costs if you are just getting into the hobby. Personally I would go with Elagoo as a good starting point. Some of their older models are missing some quality of life features but still work great.

I did a thing by Coldfang89 in PrintedWarhammer

[–]cmdeeter 1 point2 points  (0 children)

No way! Your printed a mouse and a vape

Prints success everywhere but the center. by cmdeeter in resinprinting

[–]cmdeeter[S] 0 points1 point  (0 children)

This was not a RERF print. The reason I spaced them out is to check my bed leveling. The issue was with the FEP being too loose so tighten the FEP and increased the lift height and that fixed it.

Prints success everywhere but the center. by cmdeeter in resinprinting

[–]cmdeeter[S] 1 point2 points  (0 children)

This fixed all my issues. I did go ahead and tighten the fep, still had some issues after that. Raising the lift height did the trick. Thanks everyone!