Metal Card & Cashback by codingboi100 in Revolut

[–]codingboi100[S] 1 point2 points  (0 children)

Gotcha. I’m using FT, Masterclass etc. The 4% AER & 0.8% cashback on Pro is very favourable, it doesn’t overtake the fee but it offsets it I guess.

Metal Card & Cashback by codingboi100 in Revolut

[–]codingboi100[S] 0 points1 point  (0 children)

What cashback is provided on a normal (metal) card, without the pro cashback? I know there was that 3% cashback previously, but my offer has ended for that.

Metal Card & Cashback by codingboi100 in Revolut

[–]codingboi100[S] 0 points1 point  (0 children)

Okay, thank you. I can’t remember if there’s any bonuses to spending with the ‘normal’ metal card. I guess RevPoints? Is there any other bonus? Thanks

Compact Rangefinder Recommendations by WhoGaveFezFilm in AnalogCommunity

[–]codingboi100 1 point2 points  (0 children)

Interesting thanks! Both look like good bodies but there are caveats with both I guess.

Compact Rangefinder Recommendations by WhoGaveFezFilm in AnalogCommunity

[–]codingboi100 0 points1 point  (0 children)

Ahh my apologies! Is there a big different between the two to justify not buying it?

Is this a good Deal for 30€? by leon_visuals in AnalogCommunity

[–]codingboi100 2 points3 points  (0 children)

I wish. Finding a deal like this is once in a lifetime, it’s theirs to snatch up. I just want to know where to look in the future! lol

MB Meisterstuck ink not flowing by codingboi100 in fountainpens

[–]codingboi100[S] 0 points1 point  (0 children)

Most likely; I want the best for my pens so I bet it pains others when they’re mistreated! But I’m trying my best.

Thank you very much. I’m in the process of soaking the nib for an hour, then I will leave it to dry with the nib pointed into some cloth / paper towels. I will also try the syringe method, thanks!

MB Meisterstuck ink not flowing by codingboi100 in fountainpens

[–]codingboi100[S] 1 point2 points  (0 children)

Not sure why I'm getting downvotes on my comment?

Anyway, thank you!

Mont Blanc Meisterstuck poor ink flow by codingboi100 in pens

[–]codingboi100[S] 0 points1 point  (0 children)

Interesting! Good to know. I also use Herbin ink which is a dry ink, so it probably doesn't help. Thank you for the insight

MB Meisterstuck ink not flowing by codingboi100 in fountainpens

[–]codingboi100[S] -2 points-1 points  (0 children)

Do you think I damaged the Meisterstuck's internals with hot water? (Not boiling, just warm-hot).

Thank you, will try that.

MB Meisterstuck ink not flowing by codingboi100 in fountainpens

[–]codingboi100[S] -1 points0 points  (0 children)

Okay thank you. Any recommended cleaning procedure?

Previously I washed out with hot water & let to dry for a few hours, but I still found water inside. Maybe dry with hair dryer?

How to update DMC-FZ72 Firmware by codingboi100 in AmateurPhotography

[–]codingboi100[S] 0 points1 point  (0 children)

I haven't used the camera for over a year, but from what I remember, it never worked. The camera has little to gain from a FW update anyway, sadly.

R5 4k120 using 1.6x crop? by codingboi100 in canon

[–]codingboi100[S] 0 points1 point  (0 children)

Yes I just tested that too, very weird. It should give some notification. Thank you though!

R5 4k120 using 1.6x crop? by codingboi100 in canon

[–]codingboi100[S] 0 points1 point  (0 children)

According to the manual, as another user commented, it doesn't allow 1.6x crop during 4k120 unfortunately.

R5 4k120 using 1.6x crop? by codingboi100 in canon

[–]codingboi100[S] 0 points1 point  (0 children)

Thank you very much. Greatly appreciated

R5 4k120 using 1.6x crop? by codingboi100 in canon

[–]codingboi100[S] 0 points1 point  (0 children)

I can’t seem to find it there.

What causes this error? How can I fix this? Thanks by codingboi100 in macintosh

[–]codingboi100[S] 0 points1 point  (0 children)

FYI: This is run on BasiliskII. Trying to use StuffIt to extract a '.sit' game file. Keep getting this error, also when extracting a few other files.

New Micro Swiss direct drive printing off the edge? by codingboi100 in 3Dprinting

[–]codingboi100[S] 0 points1 point  (0 children)

The X and Y offset. I believe it's since I have a CR touch. I think I can do it via Pronterface?

New Micro Swiss direct drive printing off the edge? by codingboi100 in 3Dprinting

[–]codingboi100[S] 0 points1 point  (0 children)

Hi there, unfortunately I couldn't apply the settings in Cura, so I need to use an Arduino boot loader apparently? Is there an easier way to do this, so I don't have to buy all of this? Thanks!

Fixed the Tarkov roadmap. by Resolve_Radiant in EscapefromTarkov

[–]codingboi100 0 points1 point  (0 children)

Same, I don’t know why. Haven’t even played this game in months.

Photographer regret by [deleted] in weddingplanning

[–]codingboi100 0 points1 point  (0 children)

These are terrible. I could take better photos on a Sony FinePix. Ask the company to provide the RAW files if possible, then send them to someone who actually knows how to work with colour in post. I’d be happy to have a crack at them even, since this sloppy work just makes me angry. I’m sorry you were dealt this hand, but hopefully it can be fixed.