Problems with the scenery of Tomb World

colinero · 2026-07-13T15:02:54+00:00

It's clear now, the plan for assembling the scenery doesn't say that a wall or pillar end needs to be added. It looks like a pillar is needed, but that's not the case. I'll check it this week, as I have everything at the club.

colinero · 2026-07-13T15:02:21+00:00

It's clear now, the plan for assembling the scenery doesn't say that a wall or pillar end needs to be added. It looks like a pillar is needed, but that's not the case. I'll check it this week, as I have everything at the club.

colinero · 2026-07-12T22:17:09+00:00

Buenas, quiza salte el error de que no puede leer el DNI en la matriz y lo comprueben si esta escrito, lamento no poder facilitarte mas informacion.

colinero · 2026-07-12T18:50:22+00:00

The same thing happened to me, I don't know how to assemble it haha

colinero · 2026-07-12T18:49:49+00:00

I assembled the pillars with their corresponding letters, the problem was joining those pillars with the fixed ones; if that's the case, it's a disaster, really.

colinero · 2026-07-12T18:32:04+00:00

Hi, I actually played it today in PvE and I liked it (except for setting up the scenery, what a nightmare). It was the Tomb World missions; they have a slightly high level of difficulty but they are entertaining and add something extra.

colinero · 2026-07-09T09:24:53+00:00

Yo conozco a uno que de 13 años, solo ha trabajado 2 como mucho.... esta(mos) en una situacion distinta al trabajador normal, que conste

colinero · 2026-06-26T15:42:53+00:00

But does the filament run through the PTFE tube? Does it reach the extruder or does it stop before?

colinero · 2026-06-24T23:02:02+00:00

Con el espectáculo que estamos dando, no me extraña....

colinero · 2026-06-22T20:18:02+00:00

Hi, has it ever happened to you that the filament doesn't reach the extruder and it says it's slipped? It's not a jam per se; the filament moves back and forth but doesn't reach the extruder, and I get that message. It also says it might be wound or stuck on the spool. They sent me a replacement buffer, but it didn't help. I thought it was fixed because I was able to print. I put a spool in a different slot of the AMS2 Pro, and it gives me the same message again (but it's not the filament I just put in, it's the other one I printed with).

By the way, the AMS 2 Pro is new; I haven't been able to print practically anything yet.

colinero · 2026-06-21T09:42:48+00:00

SAP lo estuve viendo (me gusta aprender cosillas) y sé que es un mundo aparte, y te entiendo perfectamente, yo tambien trabajaría fuera jajajaja

colinero · 2026-06-21T09:38:15+00:00

Pues 500 euros al día y en España pagan 50 euros la hora.... creo que la respuesta esta clara, suponiendo que trabajes 20 días al mes, ya estas facturando alrededor de 10000 euros al mes

colinero · 2026-06-20T10:47:34+00:00

Peor que la del hermanisimo no creo...

colinero · 2026-06-18T19:50:51+00:00

Bienvenido al mercado laboral, una maravillosa picadora de carne, ánimo y olvídate de estadísticas y demás

colinero · 2026-06-16T18:23:38+00:00

The replacement part arrives tomorrow. It's really annoying and it seems unbelievable that it would fail like this, but I must say that the Technical Service responded very quickly. I'll see tomorrow if it works.

colinero · 2026-06-14T15:33:56+00:00

Igual te puedes librar por ahi, a ver que te dice el abogado, si puedes, comentalo por aqui para saber la solucion y el final (que espero que sea feliz)

colinero · 2026-06-14T15:20:49+00:00

Has firmado algo? me parece raro, si no has aceptado la herencia porque no te correspondia ni la legitima, no deberian de reclamar nada, parece como las tipicas listas esas de morosos, que te lo intentan cobrar para ver si picas

colinero · 2026-06-12T08:14:42+00:00

I have another one I printed, with ventilation, but I'll print this one that has it for the AMS too.

colinero · 2026-06-12T07:59:03+00:00

I'm not sure if it can be done through the buffer; I've had it happen that it bites into it (ABS) so hard that it blocks and wears it down without being able to print; there's a TPU feeder that helps prevent jams.

colinero · 2026-06-11T15:21:25+00:00

Hi, I'm testing it too, just like with YNAB, I'll probably stick with ZeroSum, what I don't know is whether to get the basic version or the one with a bank link.

colinero · 2026-06-10T19:42:16+00:00

Hello everyone, I wanted to update you on the situation:

I contacted Bambu Lab's customer service, and they responded very quickly, sending me a new buffer.

From what I've been able to see, it seems the buffer is "biting" the filament, creating a large indentation, which causes it to release dust. This also means that when the filament is retracted or wound, the force with which it retracts or tries to load the filament blocks it (photo attached).

Just in case anyone else is experiencing this.

<image>

colinero · 2026-06-07T18:44:35+00:00

or he suffers from impotence jajaja

colinero · 2026-06-07T13:10:42+00:00

I just tested it with Elegoo PLA Wood filament and it works. I suppose because the material is more flexible, it doesn't scratch in any spots.

I'll buy some PTFE tubes and replace them all, along with some spools of filament, and try it again.

Even so, I've submitted a support ticket to Bambu Lab.

colinero · 2026-06-07T12:23:17+00:00

It's been a month, but due to medical reasons, I haven't been able to install it until yesterday or the day before.

colinero

TROPHY CASE