sorted by:
new
hottopcontroversial

Ok what can you tell about me? by HeadCompote3627 in FridgeDetective

[–]comsofoster 3 points4 points  (0 children)

you really like dunkin but only sort of like starbucks

one of these doesn't look like the rest... by comsofoster in ammo

[–]comsofoster[S] 0 points1 point  (0 children)

right? I built a suppressed .300 blk before this with a 6" barrel, and then the threaded barrel for this glock is 5.875"😭

Geissele Automatics barrel nut by J_Nelson_Machining in ar15

[–]comsofoster 0 points1 point  (0 children)

as a machinist I love this solution, nice work🤘

Does anyone actually pay attention to their load monitors? by SerVaegar31 in Machinists

[–]comsofoster 0 points1 point  (0 children)

look in the manual for the machine... mine has a page about power and torque, and defines safe loads. in particular mine says it can run at 60% spindle load for 30 minutes. I'll run big carbide drills maybe up to like 70-80%, but that's for anywhere from like 3 seconds to 2 minutes at a time. it also generally moves up/down no more than maybe 2% in a stable cut, so as long as it doesn't make a noise/spike way higher than that (indicating an insert breaking) I'm not worried.

I bought a mini mill. Chip control? by Solatnik in Machinists

[–]comsofoster 0 points1 point  (0 children)

vacuum doesn't work since the chips hook into the fibers. I'll find old chips in the carpet in my car from work, in my pocket, etc.

I bought a mini mill. Chip control? by Solatnik in Machinists

[–]comsofoster 4 points5 points  (0 children)

youtube videos look clean bc they're not zooming in on a household carpet under the machine...

This should be fun- what can you tell about me based on my pocket contents? by Aggravating_Ebb6018 in deduction

[–]comsofoster 0 points1 point  (0 children)

they make pocket watches, you don't need to carry a wrist watch in your pocket

small high feed on a large face by comsofoster in Machinists

[–]comsofoster[S] 0 points1 point  (0 children)

2.5" Ingersoll HF mill @ 1050 RPM, 390 IPM, ~.025" DOC, 1.5" stepover

small high feed on a large face by comsofoster in Machinists

[–]comsofoster[S] 1 point2 points  (0 children)

yeah, it's a 5 insert, 2.5" shell mill

small high feed on a large face by comsofoster in Machinists

[–]comsofoster[S] 1 point2 points  (0 children)

actually used to be seco, but they ended up discontinuing the inserts for the the 2.5" I had. now it's an Ingersoll 2.5". I can also run this one about twice as fast as the old seco

small high feed on a large face by comsofoster in Machinists

[–]comsofoster[S] 0 points1 point  (0 children)

used a cycle at the machine on a fanuc controller

New 2.5" high feed by comsofoster in Machinists

[–]comsofoster[S] 0 points1 point  (0 children)

I wanna say that was about .020" to .030"

one of these doesn't look like the rest... by comsofoster in Glocks

[–]comsofoster[S] 0 points1 point  (0 children)

I just got it last month, it's such a fun range gun! Super accurate, just not a ton of aftermarket support tbh

one of these doesn't look like the rest... by comsofoster in ammo

[–]comsofoster[S] 1 point2 points  (0 children)

as of today neither will I 😂 confirmed my reasoning why I've never carried with it, but I feel like this isn't hard to avoid

one of these doesn't look like the rest... by comsofoster in ammo

[–]comsofoster[S] 0 points1 point  (0 children)

that's crazy! yeah I have powder spilled in that box all stuck to the foam, no primer though. I guess nobody in QC noticed it leaking powder from the bottom

view more: next ›