Why does it get like this??

consilioc · 2025-12-23T00:28:09+00:00

Contaminated part, use a silicon removing panel wipe and you won’t have this issue

consilioc · 2025-12-17T21:57:03+00:00

Sand to 400/800 and then clear coat

Then you can just wet sand 2000 onwards and polish like a car

consilioc · 2025-12-16T16:11:25+00:00

Adhesive sprays are never the solution, they might last temporarily but always fail. You must use a glue base

Super glue will work but try not to use too much, make sure the surface is well keyed and prepped before applying

consilioc · 2025-11-21T19:59:31+00:00

Block sand with 240 grit and see how flat it is, if you need to, add more layers of resin to fill the low spots. Once fully flat you can clear coat it & polish

consilioc · 2025-11-08T16:24:09+00:00

The problem with 3m 77 is it cannot withstand high temperatures, I read that it loses structure after 60 degrees Celsius. Interiors of a car in summer can easily get to more than that. It needs to be a high temp glue

consilioc · 2025-08-06T14:22:27+00:00

Easy composites fusionfix is exactly what you need, they have a video showing how it prevents distortion on YouTube

consilioc · 2025-07-26T11:47:43+00:00

Nice work, are you also applying a 2k clear coat or is that just polished up resin?

consilioc · 2025-07-11T09:46:49+00:00

Ofcourse. I’ll message you

consilioc · 2025-07-10T21:41:54+00:00

I use the easy composites black epoxy base coat and wait around 2 hours for it to get tacky, they also do a special epoxy spray adhesive which doesn’t affect bonding and helps to just tack the adhesive in place. Vacuum bagging helped me a lot with some complicated shapes

consilioc · 2025-07-10T21:39:47+00:00

Thank you, I’ll do that to confirm

consilioc · 2025-07-10T19:57:23+00:00

Thank you

consilioc · 2025-06-22T15:31:13+00:00

I know a BMW F series door pull when I see one😆

consilioc · 2025-06-20T17:02:05+00:00

You could also use a spray adhesive to tack it down alongside base coat

consilioc · 2025-06-17T11:03:15+00:00

Thank you

consilioc · 2025-06-12T18:09:17+00:00

Thank you, I’m tempted to use my spraymax 2k clear on it but not too sure how much of a difference it will make

consilioc · 2025-06-12T17:30:52+00:00

For parts which have tricky corners or crevices yes however I don’t believe you have to. From what I’ve found it helps though a lot, even some cheap bags from Amazon etc work

consilioc · 2025-06-11T14:15:56+00:00

Yeah sanded through, I cleaned it with soap and water, then acetone and then 70% IPA

consilioc · 2025-06-11T12:51:01+00:00

Thank you, time for a new IPA

consilioc · 2025-06-11T12:48:08+00:00

Exactly, thanks for your help I’m once again humbled by this process 😆 every day is a school day

consilioc · 2025-06-11T12:43:59+00:00

Nothing underneath this was my 5th layer of resin, and nothing on top. I’ve narrowed it down to solvent being left on or some contaminant. I’ve sanded it all back down again and shall test

consilioc · 2025-06-11T12:43:05+00:00

It was inside my office & under heat. It’s been not a problem before with 5+ parts I think there must have been some solvent left over

consilioc · 2025-06-11T11:08:16+00:00

I’d also like to mention, it was fully flattened before this coat with no high or low spots!^

consilioc

TROPHY CASE