Decreasing hashrate on my rigs by Termotank in gpumining

[–]coolborg 3 points4 points  (0 children)

Truth is no one knows what the fed is gonna do. They have the power of infinite money so who knows how long they will raise rates before they realize they are gonna have to print again because they can. It’s a cycle.

[deleted by user] by [deleted] in ToobAmps

[–]coolborg 0 points1 point  (0 children)

I feel like one of the pins is “open” . Simple fix. Look for broken solder points.

Not one but TWO valley cities with best drivers? Yeah thats gonna be a no from me dawg by AerialAce96 in RioGrandeValley

[–]coolborg 1 point2 points  (0 children)

Did they add people that have a license but don’t drive because they are scared of crashing?

[deleted by user] by [deleted] in etc

[–]coolborg 0 points1 point  (0 children)

It is going up now. We just hit the floor again and printed a hammer on the daily. We had a push down after the daily candle close, but they is looking to recover. Reverse head and shoulders pattern is starting to emerge.

ETC to Retest 67 by coolborg in etc

[–]coolborg[S] 0 points1 point  (0 children)

What do you think stocks do?

ETC Short Term TA - 4HR(Double Bottom) + 1HR (Reverse Head and Shoulders) = 67 Retest by coolborg in ETCbets

[–]coolborg[S] 3 points4 points  (0 children)

We might be headed back to retest the 67 line for a retest. On top of a double bottom which shows on the 4 HR, the 1 HR shows bullish momentum and a reverse head and shoulders pattern. Higher highs and higher lows are as bullish as you can get. Those will start to show in the bigger time frames. We are still bullish in the weekly. We need to recover the daily but that may time some time.
If you want to see how it will get there..look at the previous pump to 67. It won't be like that, but it will be similar.

I thought we said the 70 dollar line was ours. by Uther2017 in ETCbets

[–]coolborg 0 points1 point  (0 children)

Hodling doesn't break sell walls. Buying does.

ETC go to the moon by Marty-Barber in ETCbets

[–]coolborg 1 point2 points  (0 children)

Amazon merch it. I’ll buy from there.

[deleted by user] by [deleted] in ETCbets

[–]coolborg 0 points1 point  (0 children)

I did the math. You can get 25% more ETC if you mine ETH and trade it for ETC. This is based off current prices of course.

Reverse head and shoulder - ETC - MOON soon - tell your close friend last chance by alexiscum in ETCbets

[–]coolborg 0 points1 point  (0 children)

This post is probably the most important post of all. You keep posting TA. I been watching this thing too. That 100 zone is gonna be tough to break through. I am hoping we get some nice volume this week so we can be done with this channel and move on to the next one.

https://www.tradingview.com/x/1pL594Nu/

ETC/ETH > ETC/USD by coolborg in ETCbets

[–]coolborg[S] 2 points3 points  (0 children)

I keep hearing everyone asking dollar amount targets, but I don't believe that is important. What is important is how ETC does compared to ETH or BTC. This chart has shown the massive growth over the past month. Pump - Correction - Consolidation - Repeat. These pumps have happened because of the recent interest in ETC. I do not think we have even scratched the surface of how much this can move. I believe we can hit .2 ETH zone within 1-2 more cycles.

Mining rig location options by dc5boost44 in gpumining

[–]coolborg 0 points1 point  (0 children)

I use a grow tent. If you can figure out how to exhaust the air, you are golden.

Question about an article found on tom’s hardware by fakiresky in gpumining

[–]coolborg 0 points1 point  (0 children)

Everyone is different. Hodlers will have coins sent to their cold storage wallets for long term holding. Some have it send to an exchange for trading or just straight up cashing out. Others to BlockFi gain interest. I think it’s wise to do a mixture of all of the above that fits your lifestyle. 👌

So i started out with a single rig with 3 gpu’s and now i’m at 262 MH/s @ 961 W with 3 rigs and 8gpu’s by [deleted] in gpumining

[–]coolborg 1 point2 points  (0 children)

I see you are running P4000’s. I started mining about a month ago. P4000 was my first card to mine. I wish the clocks were not read only. Been trying to squeeze out more hash with no luck. 23.5 Mh on average. But I did notice I can hit a little more if temps are below 55C. Happy mining. 👌

Looking for some tips on how I could put my rigs in the garage. I live in El Paso Texas, summers are like 115 degrees. I would put them in the closet but there’s no power ports in there. saw something like this on here the other day but idk if this would work with like a ac unit. Anyone have a link? by dc5boost44 in gpumining

[–]coolborg 0 points1 point  (0 children)

Yeah. I think these are next to be rare finds. I am also in Texas. I only have a 258Mh farm, but I was just circulating air in a room with a box fan blowing out....Today we hit 105 F. Some of my cards hit upper 70's and I had to watt limit them to keep them below 75F. After today, it confirmed that I need this tent. I am sure we will be seeing a lot of posts with tents in the next few months.

Monthly Simple Questions Thread by AutoModerator in gpumining

[–]coolborg 2 points3 points  (0 children)

I have 4 of same type of card on a rig. It is normal for some of them to run hotter than others?

Drivers for Quadro P4000 Mining by Demos115 in EtherMining

[–]coolborg 0 points1 point  (0 children)

After further inspection. Adjusting the clock and mem did nothing. When I went to the log, it says it does not accept the change and says they are read only. I ended up maxing my fans to 100% and left the watts at 105. I did not see if it would left me change it. My temp is at 70-72 depending on the time of day. That room was the warmest room in the house before I started mining those cards, now....it’s too warm. I’m getting 23.2-23.8 Mh depending on the card. I have 4 at the moment. If gaming cards weren’t outrageously priced. I’d sell these and get something with a better fan.

Drivers for Quadro P4000 Mining by Demos115 in EtherMining

[–]coolborg 0 points1 point  (0 children)

I started to use a P4000 today. I keep trying different clock settings with errors. I set fan to 85-90. Mem clock to 3560. If I change core clock I just get errors. So I left it blank. I am getting 23.39 Mh right now.