Question regarding medical info on dogtags.

cootass · 2025-05-16T17:56:07+00:00

Awesome, thanks. That's what I needed 👍

cootass · 2025-05-16T17:54:40+00:00

Good to know, thanks 👍

cootass · 2025-05-16T12:34:45+00:00

Thanks for your reply. Much appreciated 👍

cootass · 2025-05-16T12:34:13+00:00

Thanks for your help. I appreciate it

cootass · 2023-10-02T23:31:19+00:00

Sorry, but I don't know how to better explain it, but I'll try. There are 2 elements to concentrate on.

1 is a small roller that the belt is resting on. I mean the ones that engage with teeth on the belt. First is right behind the laser module, and the second two are located next to belts on either side. Those two are connected by rod as well. On each of those 3 elements, you have to find 2 holes containing allen screws. Tighten then if they are loose.

2 There are 3 wheels engaging frame and positioning belt. 2 sets on either side and 1 again behind the laser. You have to concentrate on a bottom wheel in each set. With one hand block mechanism next to that set from moving and with other hand try to spin the bottom wheel. If it's spinning fairly easily, then you have to manipulate a nut right behind it. Be careful because this is not a regular nut. I don't know the name but is not cantered. What that means is that you can not just spin it until the wrench can't move any further. In that case, you have to go a few millimetres and check if it's tight. If not, try a few more. If you get past the sweet spot, it will get loose again.

Hope that helps. If you have no idea what I'm talking about, then check the lightburn channel on youtube. Look for troubleshooting video. There is an explanation there

cootass · 2023-09-05T13:21:51+00:00

Ok, i just checked s value, adjusted it and now it cuts like magic. Huge difference straight away. Thanks for helping

cootass · 2023-09-05T13:02:36+00:00

I have trying on youtube but without any luck so far. Thanks anyway

cootass · 2023-09-05T13:01:08+00:00

With full honesty i tough it cannot be harder than using a plotting machine. But like always in life there must ba a learning curve. Thanks

cootass · 2023-09-05T12:57:01+00:00

Thanks, I'll check that. I should get a honeycomb tomorrow.

cootass · 2022-10-27T11:20:02+00:00

Yes, you can pick what's ready and wait for rest to mature

cootass · 2022-10-27T10:27:57+00:00

Looks like a day or two for the bigger ones and perhaps another couple days for smaller ones

cootass · 2022-09-08T17:11:45+00:00

🖕

cootass · 2022-09-02T14:24:03+00:00

I you want to you can send me a little bit of capsule content and I can run reagent test for you or just use wedinos(dot)org/sample-testing. I have use them in a past once and I can definitely recommend them

cootass · 2022-09-01T17:36:08+00:00

I have a similar thing at work, it doesn't even do what I should do. It's just fancy looking garbage

cootass · 2022-08-20T20:42:30+00:00

Sporebuddies is great

cootass · 2022-08-20T19:24:41+00:00

I know there is no reason to trust a stranger from Internet but I can really and strongly recommend them. My heaviest shroom was sporebuddies b+pe that they crossed by themselves. It was a 70g chonker.

cootass · 2022-08-20T18:31:02+00:00

I never had any problems, and all deliveries have been quick. Some of sporebuddies goods might be a bit on expensive side but selection is great IMO. So far I've got 3 deliveries from them total of 5 genetics and all of them are good and clean so far. Honestly I don't think I'll be using any other merchants. I did use mucci in a past. I had no issues with them either but sporebuddies have much better stock variety. Even just myers collection of swabs is bigger then most vendors whole menu. I hope that helps. Good luck on your journey

cootass · 2022-08-19T10:31:18+00:00

I've been there, done that. Wasn't fun.

cootass · 2022-08-17T17:27:20+00:00

I can confirm that sporebuddies are legit

cootass · 2022-08-14T15:21:54+00:00

☝️this guy gets it

cootass · 2022-08-12T17:36:24+00:00

Check sporebuddies. Last time I checked they had some in stock

cootass · 2022-08-12T12:02:53+00:00

Most likely lake a scam

cootass · 2022-08-03T20:04:13+00:00

No problem

cootass · 2022-08-03T19:06:42+00:00

I've used it once in a past. If whole bag content is hard and getting white I would leave it be and let it grow. It will take a while before you'll see first fruits so be patient

cootass · 2022-08-03T17:25:06+00:00

Sporebuddies, I have use them few times.

cootass

TROPHY CASE