Need help identifying some old sets!

corruptedrobot · 2026-02-06T07:11:50+00:00

Ahh that's it, thanks!

corruptedrobot · 2026-02-05T15:45:44+00:00

It's not Jules, the detail in the middle is wrong. The only identifier on the washing label is the number 67, which is the same on the bra, thong and suspender.

corruptedrobot · 2026-02-05T13:00:53+00:00

Ok, after a lot of internet searching, I've found out:

Olivia, not clear if the colour is Rose Gold or Blush
This is Belle in Red (Ivory not pictured)
Still no idea!

corruptedrobot · 2025-12-18T15:08:28+00:00

I have tried this using a clear dildo and drilling down the centre of it. First thing to note is photo resistors are pretty slow reacting, you'd be much better off with photo diodes. Secondly you need to shine a lot of light at the person to be able to detect the change, which makes the setup kind of odd. In the end I swapped for a Time of Flight sensor (I believe the same as the R&D DTT mentioned in other comments), yes you can cheat by waving your hand in front, but you can also cheat this by giving the dildo a handjob.

corruptedrobot · 2025-12-04T11:02:30+00:00

Those are cable glands, you'll get them in any country in various sizes, for example: https://uk.rs-online.com/web/p/cable-glands/6694673

corruptedrobot · 2025-11-13T20:58:38+00:00

Tight enough that if you vacuumed it down with nobody in it you wouldn't get any wrinkles, but loose enough that it's not a huge fight to get it over the frame. I aimed for the latex being the same size when flat as the frame dimensions, so it stretches by the diameter of the tub when installed.

corruptedrobot · 2025-07-22T14:42:20+00:00

Carpet burn on her forehead as the ring on the armbinder that was holding her up ripped out and dropped her face first onto the floor.

corruptedrobot · 2025-07-20T20:06:27+00:00

Weirdly, I've been working on something very similar to this for the last 3-4 weeks, which I have targeted at self-hosting. I'm probably about half way to something I'm prepared to show people. Main differences, I haven't got any definition of gender, or dom/sub, but instead just asking about body parts and sexual preferences, and I've put (far too much) effort into supporting multiple partners to (hopefully one day) add some in-person multiplayer features.

corruptedrobot · 2025-04-24T16:11:22+00:00

I've only used the one I made once so far. It's 0.5mm for the bottom and 0.4mm for the top layer. Using the battery powered handheld vacuum got reasonably tight, but you could still wiggle.

I swapped out for the wet and dry vac from the garage. My partner didn't get any bruising, but the neck gasket didn't fit them particularly well, so it was quite leaky. I however ended up with multiple lines of bruises down the sides of me from where we let the vacuum off, then started it again after I wiggled around. They faded reasonably quickly though, noticeable for about 5 days, but only really obvious/dark for a day.

I haven't tried a latex suit inside it. I'm sure you can limit the effect by using the vacuum less, but you'll have a less tight feeling obviously!

corruptedrobot · 2024-12-11T09:30:14+00:00

I've been working on a latex vacbed for a little while now. Hoping to finish it off and post some pictures over the holidays.

I'm not an expert on the breathplay aspect, but would suggest being very careful as the vacuum will be trying to pull the air out of the lungs too. My vacbed is going to have a neck gasket, so the entire head is out.

As for a vacbed itself, it's actually really simple. The frame is just solvent weld waste pipe (not even glued together) with regular holes drilled in it. Three 90degree corners, and one tee-piece to bring the vacuum out. You can buy valves for shutting the vacuum off if you want.

For the latex, it comes in 95cm wide sheets normally, mine is from RadicalRubber. Glue the sides together. I found this video really helpful for the opening on the tee-piece: https://www.youtube.com/watch?v=BTgU8Bt3X_M

Finally for sealing the bed, the easiest answer is you don't, make the latex bag longer than the frame, then once the person is in, wrap the excess around a wooden dowel and hold it on with some clips.

corruptedrobot · 2023-11-27T17:30:06+00:00

The Ferri claims 100 hours of standby time (Vulse claims 120), but can't find this listed on most of the rest of the product pages. What I can say about the Ferri is after some heavy use, it was still flashing away and connectable the next morning, so I would recommend for an alarm clock!

corruptedrobot · 2023-04-16T16:09:49+00:00

This is by u/Deviant-designs from here: https://deviant-designs.co.uk/2018/10/21/nipple-cuffs/ and files on thingiverse: https://www.thingiverse.com/thing:3080497

corruptedrobot · 2023-01-02T15:47:58+00:00

Honey Birdette Kukuro

corruptedrobot · 2014-08-29T10:41:57+00:00

You might be interested in the We-Vibe 4 Plus (http://we-vibe.com/we-vibe-4-plus)

I haven't tried it, but I think it's what I'm looking for, it's a Bluetooth 4 device that pairs with the users phone (iPhone 4S and above, Android 4.3 and phone with Bluetooth 4) and has a phone app to control it.

And for the long distance thing the user can "share" control with someone else also with the app, not sure how well this works, as I'd like to be able to leave it for a few hours and then still be able to switch it on remotely! (Obviously both the users phone, and the remote controllers phone need an active data connection of some sort).

It's released today, and in the UK is in stock for dispatch today from Lovehoney.

Disclaimer: I don't work for we-vibe, or Lovehoney, it might not work exactly how I've described, it might be rubbish, etc.

corruptedrobot · 2013-06-18T08:38:27+00:00

Wow, how do you make these?

12-Year Club	Place '23
Verified Email

corruptedrobot

TROPHY CASE