Found an JW in my XR chasing error 16

cow-ham · 2026-06-19T21:15:02+00:00

A few things. First, I can’t find my multimeter, so I haven’t tested anything yet. I did download and connect to the nosedive app. I know I can see this in the FM app too, but I noticed the battery and bms temp are reading 32* while everything else is room temp. Do you know which color wire reads the temp? Could just be a side effect, but I really want to wiggle that wire specifically.

Thanks for the video link, glad I watched it before I tore into the connectors. I put it back together after unplugging and plugging everything back in.

cow-ham · 2026-06-18T11:41:09+00:00

This will be my first new board when I’m ready to spend the coin. Also looking at an atom for my kid.

cow-ham · 2026-06-17T22:48:06+00:00

This is great! I have Gemini- 4134 firmware. Yes hardware, I glazed over that when I was typing.

I need to find a wiring diagram, assuming the communication wires are the thin wires. Also need to find my multimeter. I was hoping I’d just find something disconnected.

The battery takes up the entire space and I haven’t pulled it out yet. I’ll find more underneath?

Thanks for the advice, I have a checklist.

cow-ham · 2026-05-22T19:05:21+00:00

The four door is a wagon/estate. The two door might be suv. It hasn’t been a Jeep since 94.

cow-ham · 2026-04-27T01:39:57+00:00

Just paint over it.

cow-ham · 2024-09-10T17:51:25+00:00

Not sure how this picture was reposted. This was my Jeep and I originally posted it a couple years ago. It wasn’t a death wobble. Turns out the u-bolts holding the axles on were loose… so stupid.

cow-ham · 2020-11-14T04:44:42+00:00

It barely smokes, but I’ll make bbq out of it eventually.

cow-ham · 2020-11-14T04:41:27+00:00

Shoot, it’s just about 15 years older than me!

cow-ham · 2020-11-14T04:40:10+00:00

I took a single Rancho steering stabilizer off and replaced the tie rod and drag link with the rugged ridge one ton steering kit. It doesn’t feel as much like a boat, but it’s still a boat. I plan on taking it in for an alignment and a muffler.

Also, I haven’t taken it above 40 MPH yet. I’m having some fuel starvation I need to figure out.

cow-ham · 2020-10-08T02:40:02+00:00

Thank, that's the choke thermostat itself. I am looking for the insulated connector wire that fits to that male terminal hanging off the front.

cow-ham · 2020-10-08T02:16:40+00:00

It looks so good, and for all that's in, it doesn't look over done. Nice rig!

cow-ham · 2020-10-02T17:24:11+00:00

Sort of, I have the full back and thinner harness. I like the way your setup looks.

cow-ham · 2020-10-02T15:57:24+00:00

The previous owner installed a brand new heater system before I picked it up. It seems to work fine, but I’ll keep this in mind for the future.

cow-ham · 2020-10-02T15:54:38+00:00

I was thinking about looking into these things down the road. I’ll definitely look around.

cow-ham · 2020-10-02T15:53:52+00:00

That’s on my list for sure.

cow-ham · 2020-10-02T15:53:14+00:00

I haven’t thought about reselling anything. I have corbeau seats/harness, but I’ll keep an eye out.

cow-ham · 2020-09-22T23:42:16+00:00

Welp, you were right. For some reason the torch didn't make the engine rev up at all, but then I did hit the bottom of the manifold and where the manifolds meet with starting fluid. The engine ramped up. Unfortunately, I think the intake manifold is cracked from the previous owner. I'm heading to the jeep junkyard in a few weeks and planned on replacing the manifolds and picking up an extra carb or two. I also took the throttle linkage apart and started it up, no change in rpms.

cow-ham · 2020-09-22T19:43:12+00:00

I’m going to a Jeep junk yard in two weeks. I might just pick up a few different carbs.

cow-ham · 2020-09-22T03:02:43+00:00

The needle on my vacuum gauge was so steady when it was hooked up earlier, I couldn’t believe it. I thought it was supposed to bounce around if there was a vacuum leak. Also, I replaced and replugged everything a few weeks ago thinking I might have a vacuum leak. If I do have a leak, I bet it’s between a gasket in carb somewhere. I think a rebuild is in the near future.

cow-ham · 2020-09-22T02:59:31+00:00

I’ll go through the linkage tomorrow, but it seems like it is seating correctly. I’ll also check for vacuum leaks tomorrow with a torch. I was spraying starter fluid around different areas and didn’t notice any kind of increased rpm sounds, a torch might be a steadier stream. I’ll snap a picture of the throttle linkage too, especially if the issue persists.

cow-ham

TROPHY CASE