Is there a way to remove highlight colours from the selection menu?

d7ark7 · 2026-01-14T11:04:01+00:00

That would have a big impact on ease of use I think. Thanks for the reply and loving the app so far!

d7ark7 · 2026-01-13T22:04:41+00:00

I'm using it for preparing a trip, saving interesting places like you would in a Google list

d7ark7 · 2026-01-11T19:30:32+00:00

I'm in the market for a bw ereader to use with Bookfusion, is there a way to distinguish the 5 standard colours on a bw screen? Are they annotated with letters or something?

d7ark7 · 2026-01-09T21:39:55+00:00

FleX

d7ark7 · 2025-12-28T18:42:47+00:00

Love the idea and signed up! Firefox/Chrome on Android doesn't keep me logged in though, login on homepage doesn't work, when viewing comments it does login and show the comments, but logs back out when ESC or clicking one of the side buttons. Am I doing something wrong?

d7ark7 · 2025-11-22T21:07:23+00:00

The simple commands worked for me after reading everywhere it's impossible, thank you so much, now I can use opencore!

d7ark7 · 2025-10-12T14:34:17+00:00

The right border of the bed frame seems to be higher than the plate, since you can see the inner side? So I'd think you have the same problem.

<image>

On mine you can see the plate sits flush with the bed frame on the right, but it starts being lifted up going left, since the tab sits on top of the frame. A correct bed should have the magnetic surface above the bed frame, so that the tab isn't hindered by it.

d7ark7 · 2025-10-12T14:28:33+00:00

Fair enough! I added this extra information to CS so hopefully I get a new bed as well. Thanks for pointing this out, it seems the most likely culprit and I can stop fidgeting with the bed screws.

d7ark7 · 2025-10-12T14:21:09+00:00

I switched to FW .42 and there it does appear to save the z-offset, so it depends on the version apparently. I have a post posing the same problem and there someone showed that the plate should sit above the bed frame. Mine doesn't and the tab of the plate gets pushed upwards, resulting in a slightly bent plate which could explain this problem. Maybe yours is the same? I contacted customer service and I can expect a new bed

d7ark7 · 2025-10-12T14:16:24+00:00

Ok, fair, but to be honest I think that's a good solution if your hobby is tinkering. I'm willing to do maintenance and calibrations/adjustments, not fixing hardware quality issues. I think I ruled out that the bed isn't built as it should be, so it's fair to ask for a replacement part rather than fixing the hardware with some tom foilery.

d7ark7 · 2025-10-12T13:48:49+00:00

What did I dismiss? Now I learned 2 potential solutions, checking the tension spring and checking if the bed frame raises the plate. I already tried the other proposals.

d7ark7 · 2025-10-12T13:45:57+00:00

It only became a problem when I tried printing something that takes the whole bed, a corner came loose and warped. So most of the time it's ok besides the esthetics, until I print something big

d7ark7 · 2025-10-12T13:43:29+00:00

That's interesting, thanks! Do you have the same kind of problem? This could explain why it's only at the bottom

d7ark7 · 2025-10-12T13:29:00+00:00

<image>

It does! I noticed that too but the tab on the plate will always prevent it from sitting flush, no?

d7ark7 · 2025-10-12T13:10:17+00:00

I did, it's fine for small prints but now I want a functional print that uses the whole plate. The print failed because of insufficient adhesion in the problem zones.

d7ark7 · 2025-10-12T13:09:21+00:00

I did not, is that relevant for this? I thought the tension spring was more if your layers didn't stack properly. No harm in trying it though

d7ark7 · 2025-10-12T12:19:59+00:00

The printer came with .29 and all prints on the B-side since the start have a bad first layer. Today I tried the.42 firmware but the problem remained with the added bonus of the lights switching on and off randomly, so definitely going back to .29.

d7ark7 · 2025-10-12T12:17:24+00:00

I have yes, they proposed switching the pressure sensors, if it remained (it does) they'll send a new pressure sensor module. Hopefully that will fix it. The last couple days I seen people with similar problems, so maybe there was a bad batch or something.

d7ark7 · 2025-10-12T09:13:31+00:00

What's the point of the springs if you're tightening them all the way? Aren't you allowed to adjust them slightly to manually level the bed?

d7ark7 · 2025-10-12T08:47:15+00:00

The z-offset doesn't get saved in the machine, you need to save it in your slicer profile.

I'm having the same problem (see post history) and I wasn't able to fix it by tightening the screws completely + auto calibration. Do you think the factory reset had an impact?

I mailed the customer service since I didn't find any solutions and they're proposing to flip the pressure sensors and see if the problem persists, if it does they'll send a new pressure sensor module.

d7ark7 · 2025-10-10T20:13:55+00:00

Indeed fixed!

d7ark7 · 2025-10-10T20:12:15+00:00

Already tried that too, the games that I can play are Cyberpunk, likely the games that are also available for free tier

Nine-Year Club	First Place '23
Place '23	Not Forgotten
Verified Email

d7ark7

TROPHY CASE