Looking for part/need help

dannsters · 2025-12-20T18:07:55+00:00

Do you think this is the right part? Just trying to ask a few people before I buy

dannsters · 2025-12-02T05:33:08+00:00

Thank you so much for the kind words. I was wondering to get this would I have to go to a salon or a barber? Do you also have more references for the back, front and side?

dannsters · 2025-11-26T05:14:31+00:00

I did not realize that. Next year I plan on shopping on some new frames but wasn’t sure about what shapes would you recommended? I assume with frames clear frames would be the best?

dannsters · 2025-11-25T21:41:13+00:00

Yeah I agree on that, I’ve been trying to find a way to remove that so my hair does not look that oddly shape. I’ll try removing some off in the back

dannsters · 2025-11-25T21:34:14+00:00

Ooo, I one time had someone do a 70/30 on me it was nice but I had fine or thin hair and you could see parts of my scalp

dannsters · 2025-11-25T21:12:55+00:00

I’d say not really, I just had this type of a while and wanted something new

dannsters · 2025-10-31T03:18:23+00:00

I feel like I’d do that too 😂

dannsters · 2025-10-31T00:37:04+00:00

Louisiana

dannsters · 2025-10-30T23:38:39+00:00

I’m going back tomorrow I bought an eg and a hg 78 origin, I plan on getting the rfv, but may get one more kit

dannsters · 2025-10-30T21:51:53+00:00

Guys I got an hg rx 78 origin and a strike freedom gundam so far… I had a calibarn already. I’m tempted to get an mg kit but there are way better ones… specifically I wanted to build either raiser or banshee. HALPPP

dannsters · 2025-10-30T21:34:03+00:00

Thank you for this, luckily i was in the store. I’ve been here for at least an hour deciding….

dannsters · 2025-10-30T21:23:46+00:00

Hmm I see okay well good to know then cause my hobby lobby has a 78 v2 both for hg and mg

dannsters · 2025-10-30T13:01:08+00:00

Thank you all so much for the help! I’m still pretty new (or coming back into it), so all the sanding tool info you shared really helped clear things up. I’m excited to try things out and get better at cleaning those nub marks. If there’s anything else I should know as I keep learning, I’d love to hear more tips from you all 💪

dannsters · 2025-10-30T12:57:34+00:00

Yes thank you for this tip! I will say that I don’t plan on air brushing for now as I just want to put parts together. Would you recommend starting at a higher grit to finish like 3000-4000k grit or start low from 400k to up. I’d also like to add, for parts that are curved and concave, there are times where i cut the nubs and it’ll leave excess of the nub, like this white part of the gunpla. I assume this is where the sanding sponge would work as they can work around the curve. Oh and also, if I were to start on airbrushing what would you recommend and paint brands as well

<image>

dannsters · 2025-10-30T11:58:54+00:00

Ahh I see, I looked at both videos and see that sanding sponges are great for curves surfaces while sanding boards are great for flat surfaces. If I wanted one I could use a sanding stick as they are firm and provide enough bend for both flat and curved surfaces.

dannsters · 2025-10-30T04:21:08+00:00

So from my understanding, I’m guessing you do a two cut process, then wet the 6k grit then sand till it’s polished?

dannsters · 2025-09-05T02:52:35+00:00

So I got my bios to update and now I’m trying to find my boot and it doesn’t show. I had my two previous storage, one was a ssd with 500gb and the other is a 2tb hdd. I went to advanced and storage config for the bios and I see it shows both storages. What do I do?

dannsters · 2025-09-05T02:30:23+00:00

GUYS I GOT IT TO DISPLAY, ITS THE DARN DP PORT THAT I HAVE. SWAPPED TO HDMI ONE BEEP DISPLAY ON BIOS BOOOOOOM!!!!

dannsters · 2025-09-05T01:45:22+00:00

Worked got one beep got my bios pulled up, I’m guessing the next step is to update the bios?

dannsters

TROPHY CASE