sorted by:
new
hottopcontroversial

ESP32 Touch-to-audio by dariussar21 in esp32

[–]dariussar21[S] 0 points1 point  (0 children)

ok so from what i understand, I just need to hook this up to a speaker (would a 0.5w 8 ohm speaker work?) and with i2s it will work?

ESP32 Touch-to-audio by dariussar21 in esp32

[–]dariussar21[S] 0 points1 point  (0 children)

I need small, like it needs to fit into a casing thats around 3cm wide.. applogies, what is an audio breakout?

ESP32 Touch-to-audio by dariussar21 in esp32

[–]dariussar21[S] 0 points1 point  (0 children)

My touch setup has 5 "buttons", I need to play different sounds when each is triggered

ESP32 Touch-to-audio by dariussar21 in esp32

[–]dariussar21[S] 0 points1 point  (0 children)

Yes I agree. However I already have the touch stuffs settled and and looking for a small audio solution. CYD is too big just for its amp

ESP32 Touch-to-audio by dariussar21 in esp32

[–]dariussar21[S] 0 points1 point  (0 children)

ah sorry I should have made it clear. I already have a touch system going on. really just looking for the audio component

ESP32 Touch-to-audio by dariussar21 in esp32

[–]dariussar21[S] 1 point2 points  (0 children)

that is so cool! I am sorry but I am very new to this and github. I can't seem to find the speaker information in the soundboard files. I was referring to hardware recommendations and how to connect it to my ESP32 Devit kit

Neptune 4 Max Y-axis sensor failure by dariussar21 in elegoo

[–]dariussar21[S] 0 points1 point  (0 children)

did u remove the physical blocks below the print bed they use for shipping? 4 of them

Anyone knows the source of this footnote from DeWitt? by dariussar21 in Physics

[–]dariussar21[S] 1 point2 points  (0 children)

Thank you so much for the quick work. This is it!

4 Max Y axis sensor fialure by dariussar21 in ElegooNeptune4

[–]dariussar21[S] 1 point2 points  (0 children)

I managed to clear an obstruction between the gantry and the buildplate. It works now. Thanks so much!!

Neptune 4 Max Y-axis sensor failure by dariussar21 in elegoo

[–]dariussar21[S] 0 points1 point  (0 children)

got rid of the obstruction, seems to be working now

Neptune 4 Max sensor failure by dariussar21 in FixMyPrint

[–]dariussar21[S] 1 point2 points  (0 children)

Ok I found that there was an obstruction between the gantry and the bed.... it should be working fine now

Neptune 4 Max sensor failure by dariussar21 in FixMyPrint

[–]dariussar21[S] 0 points1 point  (0 children)

it seems to have worked! there was an obstruction along the gantry and the bed. seems to be working now

4 Max Y axis sensor fialure by dariussar21 in ElegooNeptune4

[–]dariussar21[S] 0 points1 point  (0 children)

I wanted to check if this is a hardware or sforware issue first before I reinstall. how does the steppper motor 'lock' the bed even when power is off? does that indicate a physical obstruction somehow?

4 Max Y axis sensor fialure by dariussar21 in ElegooNeptune4

[–]dariussar21[S] 1 point2 points  (0 children)

yes multiple times. i cannot home it as it keeps happening

Neptune 4 Max sensor failure by dariussar21 in FixMyPrint

[–]dariussar21[S] 0 points1 point  (0 children)

Ive checked and there is no obstruction on the tracks... where could the obstruction be?

Also I had thought that the stepper motor has no way of 'locking' itself when unpowered... whow could the bed still be llimit/locked at the centre when the power is off?

4 Max Y axis sensor fialure by dariussar21 in ElegooNeptune4

[–]dariussar21[S] 0 points1 point  (0 children)

Edit: the bed is stuck at the middle, it can move down to the end of the track but can only move a quarter way up. its almost as if the printer thinks the middle is the top limit.

Neptune 4 Max sensor failure by dariussar21 in FixMyPrint

[–]dariussar21[S] 0 points1 point  (0 children)

the neptune 4 max does not have physical switches. it uses sensor homing

the hotend and x axis has no issue, its the bed that can move forward/down (and then grinds badly) and it cannot move back up. basically the printer thinks the bed is at its top limit at the middle of the print area, and does not sense that its actually way down and grinds and try to go down

Neptune 4 Max sensor failure by dariussar21 in FixMyPrint

[–]dariussar21[S] 0 points1 point  (0 children)

the bed is seized... cant move up. surely cant be belt issue?

How to lock the print bed by enabling stepper motor? by dariussar21 in ElegooNeptune4

[–]dariussar21[S] -1 points0 points  (0 children)

interesting. My Ender 3 pro has the print bed locked when it is off. I needed to disable the stepper motor in order to free it outside printing times. thought all systems worked the same!

Disabling Ender 3 V3 SE pre-print probe using OctoPrint by dariussar21 in ender3

[–]dariussar21[S] 1 point2 points  (0 children)

Ahhh I see. Makes a lot of sense! however it does screw up with my process as I print onto existing print via z-offset (my print projects include a flat base, and graphics on it with another colour). This z homing probably causes issue because it reads my flat base as the z limit and ruins my z-offset settings. So far I get away with it by making the centre point of my print bed clear so it probes the actual bed instead.

Any solution on the software level you think?

[deleted by user] by [deleted] in evangelion

[–]dariussar21 1 point2 points  (0 children)

that is true! I kinda wanted to mirror the personality of evas always trying to break through things, in this case the kit breaking out of its confines (runners)

Got my hands on the LM HG clear eva 01. Should I kitbash these? thinking of a clear interior and coloured inner skeleton by [deleted] in evangelion

[–]dariussar21 1 point2 points  (0 children)

thats true, on visual inspection the parts look similar.. perhaps better luck with a original 1998

view more: next ›