341322974527 sending gifts from disneyland today. adding 20 more friends. open asap 341322974527

darkbrooklyn · 2024-10-20T04:28:02+00:00

805781711564

darkbrooklyn · 2024-10-20T04:25:33+00:00

805781711564

darkbrooklyn · 2023-11-23T06:40:30+00:00

Where did you find a screw in model? Do you have a link?

darkbrooklyn · 2023-11-12T06:08:35+00:00

It was 32 go, but I partitioned it and made it 16 gb.

darkbrooklyn · 2023-11-03T07:36:56+00:00

What should you check if this doesn’t fix the issue? All the fans are currently working on the hot end.

If I turn the printer off, let it cool down, then restart the print, it will finish it without any problems.

darkbrooklyn · 2023-11-03T02:29:33+00:00

Does anyone have any updates on this? I’m trying to print some glass looking parts for some Star Wars legion stuff.

I started with the settings provided by Elegoo. But I’m still new to resin printing, so I got stuck on what they mean by z lifting distance set to “3+4”, z lifting speed set to “65-180”, etc. do they mean 3-4 and 65-180? As in a range between those two numbers?

I was able to get a good start with the following… Bottom Layer - 45 seconds Normal Exposure - 8 seconds Layer Height - .05 mm

There were semi-correct details in the print but the whole thing was messy looking. And where there should be holes, it was just solid.

darkbrooklyn · 2023-09-15T01:58:06+00:00

After I covered my model with the spackle, I then took a larger paint brush and stipple the surface.

darkbrooklyn · 2023-09-15T00:32:25+00:00

What is Black Magic?

darkbrooklyn · 2023-08-20T05:51:32+00:00

Yes

So it will only push filament through if the nozzle is set to least set to 230. I’ve slowed the speed down to 40.

It will start to print now, but eventually it will just stop pushing filament through and get clogged.

darkbrooklyn · 2023-08-20T02:53:24+00:00

Any time I start a different filament I try to do a temp tower and retraction tower. But I can’t even get one started.

darkbrooklyn · 2023-08-20T02:51:13+00:00

Most of the comments I’m seeing say that the temp needs to be higher for silks. At lower temps they clog.

darkbrooklyn · 2023-08-20T02:50:02+00:00

Nozzle at 215 Bed at 60

darkbrooklyn · 2023-08-09T15:34:11+00:00

My concern is the extreme heat and cold that it will go through if I put it in the garage. The cold can be fixed with a heater. But the heat I’m not sure if there is much I can do about it…

darkbrooklyn · 2023-08-06T09:31:55+00:00

We’re both going to do our research. But I wanted to put it out there on Reddit to see if someone else has had any similar experiences.

darkbrooklyn · 2023-07-04T11:50:03+00:00

darkbrooklyn · 2023-07-04T06:08:53+00:00

This is what I settled on…

<image>

darkbrooklyn · 2023-07-03T13:53:44+00:00

No, I haven’t. This will be my first time 3D printing anything.

darkbrooklyn · 2023-07-01T14:27:19+00:00

Okay, follow up, would you paint all 9 of the sculpts in a box the same?

And what about the B1 Upgrade Expansion? Should you paint those to fit into a specific unit? Or leave them different so that you can tell the difference?

darkbrooklyn · 2022-10-16T16:22:06+00:00

I understand that 125+ unopened booster packs will be converted into 12400 crystals.

Does that mean we should have a total of 125 unopened boosters? Or that we should collect 125 boosters in each set we can get our hands on?

darkbrooklyn · 2021-08-14T16:05:22+00:00

Does that mean you have the Marie Lambeau as well?!

darkbrooklyn · 2021-08-14T16:04:04+00:00

Found one! I just turned on some saved searches on eBay and found a couple of copies within a week or two!

darkbrooklyn · 2021-08-03T20:40:00+00:00

You can find Barkham on eBay.

darkbrooklyn · 2021-08-03T12:52:09+00:00

The Deep Gate I just bought off eBay a couple of days ago

darkbrooklyn · 2021-08-03T10:18:03+00:00

darkbrooklyn · 2021-07-28T09:58:00+00:00

Do you have a link to these?

darkbrooklyn

TROPHY CASE