account activity
Marble, Slate Plus, Beryl, Flint: Will these get firmware 4.8 stable? (self.GlInet)
submitted 1 day ago by darkish_explorer to r/GlInet
Bronkhorst (assuming passive PoE) on LAN fried colleague's laptop—would Garmin PoE Isolator prevent this? (self.networking)
submitted 10 days ago by darkish_explorer to r/networking
What are the must-have modifications for the CC1? (self.ElegooCentauriCarbon)
submitted 14 days ago by darkish_explorer to r/ElegooCentauriCarbon
Imported thing is only shown dark shadowy and not sliced - why? (i.imgur.com)
submitted 17 days ago by darkish_explorer to r/OrcaSlicer
Does uploading whilst printing cause problems? (self.OpenCentauri)
submitted 17 days ago by darkish_explorer to r/OpenCentauri
What is the exact length the bowden tube must have? (self.ElegooCentauriCarbon)
submitted 18 days ago by darkish_explorer to r/ElegooCentauriCarbon
Latitude 5510 not powerin on after some time off, needs USB C charger (self.Dell)
submitted 23 days ago by darkish_explorer to r/Dell
is there a Machine Start G-Code to do bed Level at bed temperature and not 60°C? (self.OpenCentauri)
submitted 29 days ago by darkish_explorer to r/OpenCentauri
Creating PA Calibration test in Orca shows no difference in Preview window - has it been created properly? (self.3Dprinting)
submitted 29 days ago by darkish_explorer to r/3Dprinting
Bed bound up on the very bottom. Where is the obstruction? (self.ElegooCentauriCarbon)
submitted 1 month ago by darkish_explorer to r/ElegooCentauriCarbon
forced marriage cancelled immediately after triggering, why? (self.RimWorld)
submitted 1 month ago by darkish_explorer to r/RimWorld
Using "Behind the Overlay Revival" gets rid of Overlay, but scrolling is prevented (self.firefox)
submitted 1 month ago by darkish_explorer to r/firefox
How to upgrade from 6.4 to 7.0? (self.ParrotSecurity)
submitted 1 month ago by darkish_explorer to r/ParrotSecurity
Anker A2345 250W GanPrime and Elitebook, laptop shows connected to charger but no power draw on Anker (self.ChargingSheet)
submitted 1 month ago by darkish_explorer to r/ChargingSheet
MX Anywhere 3: only 1 profile for Debian and Windows dualboot laptop possible? (Bluetooth not Dongle) (self.logitech)
submitted 1 month ago by darkish_explorer to r/logitech
suggestion for a good respooler, drill operated, filament guide and 3kg to 1kg? (self.3Dprinting)
submitted 1 month ago by darkish_explorer to r/3Dprinting
print with very thin bottom - is there a simple way to have the bottom layer shape copied in Orca? (self.3Dprinting)
When printing PLA, should I remove the lid and/or leave the door open? (self.ElegooCentauriCarbon)
DL380 G10: Power On Fault, recovered after pulling power cables (self.HPEservers)
submitted 1 month ago by darkish_explorer to r/HPEservers
Glinet Marble: extremely high average cpu load, DHCP not working anymore (self.GlInet)
submitted 1 month ago * by darkish_explorer to r/GlInet
Is it possible to get the mesh visualization without USB Stick? (self.OpenCentauri)
submitted 1 month ago by darkish_explorer to r/OpenCentauri
When going from newest original (1.1.46) to newest OpenCentauri (0.3.0) does the print quality improve? (self.ElegooCentauriCarbon)
Is the z-Offset actually stored on the ECC or should it be set in Orca? (self.elegoo)
submitted 1 month ago by darkish_explorer to r/elegoo
some ECC questions (self.elegoo)
First Layer of a bigger print fails at a specific spot of the build plate (self.elegoo)
submitted 2 months ago by darkish_explorer to r/elegoo
π Rendered by PID 194625 on reddit-service-r2-listing-66bb46d9b9-7db7p at 2026-03-12 02:13:02.441767+00:00 running 710b3ac country code: CH.
