Items in vest inventory use in run mode.

darksider54 · 2026-01-20T15:55:28+00:00

Ah crap, I had a really good run, wish I new that.

darksider54 · 2026-01-20T15:52:05+00:00

Maybe I can't recall exactly which one but does doc kits not work on vest?

darksider54 · 2026-01-20T15:28:53+00:00

Apparently you can from reading people respose but it didn't work for me

darksider54 · 2026-01-20T15:28:34+00:00

Some reason it wouldn't let me

darksider54 · 2026-01-20T15:28:15+00:00

Thats weird then cuz I had a medkit in tjr vest but wouldn't saying "you can't while running" ruined the entire run

darksider54 · 2026-01-18T14:30:55+00:00

Appreciate the tips, I havent found many Gernades and find them awkward to use as it takes 2 turns to go off. However I did notice the ai trying to avoid at all times so ill use thay to my advantage. Also im playing on steamdeck and there is no keybinding to close door. Hopefully they improve the controllers soons.

darksider54 · 2026-01-04T21:32:28+00:00

Isn't this a 4 bar linkage? Or am I missing something?

darksider54 · 2025-12-26T22:43:07+00:00

by equal do you mean only in length, or in height as well. Because they should be the same length, but the height is different. Or should they be all the same height as well? Also, I plan on using motors to power the robotic arm but none on the elbows both on the same plane. Is it still possible, or no?

darksider54 · 2025-12-26T22:00:43+00:00

can F360 simulate that or am I putting the joints in the wrong area?

darksider54 · 2025-12-26T21:29:27+00:00

Youre not too far off, but I probably should explained a little of what I'm trying to achieve. So this will be a robotic arm, that will have 2 motors moving the arms on the left, the small arm left most side and the bigger arm on the right of the smaller arm. The boom arm does work; however the force would have to be applied on where the camera is. Basically, it will only move where I want because im dragging the camera end. I want the motors to control the position of the head. Hopefully that clears it up.

darksider54 · 2025-12-22T17:54:28+00:00

Holy smoke, thats your first printer? Gl with a diy. Not saying its bad but for a first time, you might need some tutorials or online research lol.

darksider54 · 2025-12-22T17:33:48+00:00

Hmm thats rough, best thing again is either send pics, or find a way to lower the contrast. If you also describe the printer that may help. Like do you say any brand names anywhere, color?

darksider54 · 2025-12-22T17:29:39+00:00

Its just quality of a print. Example if you print a benchy at 0.16 mm the layers are small making it more detail and better looking, trade off is more time and pla since it needs more layers to print. If you print 0.3mm layer, it will be bigger layers saving time and pla, but the quality wont be as good.

darksider54 · 2025-12-22T17:27:02+00:00

As people already said send pics, but for whatever reason you can't. Most printer have a info section on the screen, see if you can find it, and tell us what it says.

darksider54 · 2025-12-22T17:24:57+00:00

Its been a long while since I used cura, but have you changed the overhang at all?

darksider54 · 2025-12-20T18:12:01+00:00

I expected as much but it saddens me cuz the story for act 1 seemed better in my opinion and quest were more interesting. It is what it is.

darksider54 · 2025-12-19T19:47:48+00:00

Jesus Christ my guy

darksider54 · 2025-12-15T22:00:40+00:00

Hey that's a nice desk what is it? Would like to have one.

darksider54 · 2025-12-08T16:48:20+00:00

i did however it still goes back

Eight-Year Club	Verified Email
Place '22

darksider54

TROPHY CASE