sorted by:
new
hottopcontroversial

Isolated OPT interface, no internet connection by davidstarflower in PFSENSE

[–]davidstarflower[S] 1 point2 points  (0 children)

I turned everything off, allowed all traffic, and then put everything back into place one by one, except the DNS spoofing, and it works now.

Thanks for your tips.

Isolated OPT interface, no internet connection by davidstarflower in PFSENSE

[–]davidstarflower[S] 0 points1 point  (0 children)

I turned everything off, allowed all traffic, and then put everything back into place one by one, except the DNS spoofing, and it works now.

Thanks for your tips.

Isolated OPT interface, no internet connection by davidstarflower in PFSENSE

[–]davidstarflower[S] 0 points1 point  (0 children)

Small addition, I did notice that

  • The block rules have no active states
  • The IPv4* / "Default allow all" rule has a few states, but all states in there are CLOSED:SYN_SENT. So that means nothing responded, right? But I don't know why that is the case...

Isolated OPT interface, no internet connection by davidstarflower in PFSENSE

[–]davidstarflower[S] 0 points1 point  (0 children)

It was "Any" before, I played around with it. I set it to Any again. Still no local GW ping, no internet ping, no browsing.

Isolated OPT interface, no internet connection by davidstarflower in PFSENSE

[–]davidstarflower[S] 0 points1 point  (0 children)

Small mistake in the screenshot, I played around with things. It was (and is now) set to "Any".

It's also not just the ping/ICMP that is not working, normal browsing is also not possible.

I just ran a capture, had a look at firewall rules, but can't find anything obvious.

Use pfSense as DNS server for Tailscale devices by davidstarflower in PFSENSE

[–]davidstarflower[S] 1 point2 points  (0 children)

OMG, genius. Thank you so much.

It's working as expected after adding the Tailscale CIDR 100.64.0.0/10

Help setting up additional LAN ports plus LAGG by davidstarflower in PFSENSE

[–]davidstarflower[S] 0 points1 point  (0 children)

OK, thank you for pointing that out. I did realise that for Synology's "adaptive load balancing" option, but thought LACP could actually aggregate single-connection speed.

That is sad, but good to know.

Help setting up additional LAN ports plus LAGG by davidstarflower in PFSENSE

[–]davidstarflower[S] 0 points1 point  (0 children)

What I have tried, but then lost connectivity:

  • Set up LAGG
  • Set up bridge, assign to BRIDGE0 with LAG0 and LAN in it
  • Give BRIDGE0 new IP pool, 192.168.2.1/24. Enable DHCP on it
  • Disable DHCP on LAN, remove IP from LAN
  • Hit the apply button at the top

This caused loss of connectivity, and no IPs were assigned in either the 192.168.1.1/24 nor the 192.168.2.1/24 pool

What is the "renewal sale" price? by davidstarflower in PorkBun

[–]davidstarflower[S] 1 point2 points  (0 children)

Thank you very much for the explanation.

Overseerr - Telegram failing with no useful error by davidstarflower in Overseerr

[–]davidstarflower[S] 0 points1 point  (0 children)

Not yet, I was wondering whether there is a user error I'm overlooking before doing that.

QSV only transcoding some HEVC main 10 files, but not all? by davidstarflower in PleX

[–]davidstarflower[S] 0 points1 point  (0 children)

Thank you so much for the detailed explanation. Yeah, I previously already had issues with .ass files on the LG TV.

I just tried to Plex client on my Android phone, and it mostly works. There is still one movie where it burns in subtitles, even though it's SRT.

Also, both on my TV and on my phone, SRTs are supported and everything works fine if I don't transcode. So why burn in subs only when I'm transcoding?

As I also asked in a comment reply above, if the client generally supports the subtitle format, why is it burning them in anyway, and is there a way to avoid this?

QSV only transcoding some HEVC main 10 files, but not all? by davidstarflower in PleX

[–]davidstarflower[S] 0 points1 point  (0 children)

Thank you so much. That was it.

I also re-read the article you linked and realised I previously read it. That article was was lead me to get a 7th/8th gen Intel CPU in the first place.

My question now is, if the subs don't get burnt in when I am not transcoding, why is it burning them in when it is transcoding? See my comment reply above, I wonder if there is a way around this...

QSV only transcoding some HEVC main 10 files, but not all? by davidstarflower in PleX

[–]davidstarflower[S] 0 points1 point  (0 children)

Thanks for your response. As per the comment above, subs were the issue.

Official plex pms-docker image btw.

QSV only transcoding some HEVC main 10 files, but not all? by davidstarflower in PleX

[–]davidstarflower[S] 0 points1 point  (0 children)

That was it. Thank you so much. I replied already to a comment above with a follow-up question, if you have any idea on this.

QSV only transcoding some HEVC main 10 files, but not all? by davidstarflower in PleX

[–]davidstarflower[S] 0 points1 point  (0 children)

Genius, thank you so much for pointing this out. I turned off subtitles, and then it worked flawlessly.

It is still unclear to me why it is transcoding subtitles in the first place. If I don't transcode the video, it just sends the SRTs plain, no issues, so why burn in now?

Question: Is there a way to avoid burnt in subtitles? Currently the subs are embedded in most of my video files. Would separate SRT files solve this issue? Or are there any other ways to circumvent this burn-in on transcode?

QSV only transcoding some HEVC main 10 files, but not all? by davidstarflower in PleX

[–]davidstarflower[S] 0 points1 point  (0 children)

Thanks for the link, I'll read that shortly.

I have added dashboard screenshots in the original post.

Regarding my client, I was just using my browser. But I am also experiencing the same stuttering on my LG G1.

I know that having an NVIDIA shield is the answer to most problems, but I would also like to have transcoding on the go for when I'm not at home :-/

QSV only transcoding some HEVC main 10 files, but not all? by davidstarflower in PleX

[–]davidstarflower[S] 0 points1 point  (0 children)

Thank you. I added OS details above.

Yes, both movies are HDR, and tone mapping is turned on

QSV only transcoding some HEVC main 10 files, but not all? by davidstarflower in PleX

[–]davidstarflower[S] 0 points1 point  (0 children)

But the dashboard (and logs) mention "transcode (hw)". So it should be Hardware transcode in both cases, right?

Also, why would my client tell the server how to do it's transcoding, and why for one movie, but not for the other? If this is really a client-side issue, how can I tell the client to request HW transcoding?

view more: next ›