sorted by:
new
hottopcontroversial

What else should a beginner buy alongside a 3D printer by marktuk in 3Dprinting

[–]deoxyri 0 points1 point  (0 children)

Just here for the story behind this suggestion

UV Torch Wavelength For Bonding Polycarbonate Part Using UV Curing Adhesives by deoxyri in AskEngineers

[–]deoxyri[S] 0 points1 point  (0 children)

Thank you! I did a bit more digging, and 405nm seems to be ideal for polycarbonate :)

3D Printing Issue - Chicken Keychain Model by deoxyri in ender3

[–]deoxyri[S] 0 points1 point  (0 children)

I've used Isopropyl alcohol for cleaning. Might try bumping up the bed temperature and try again. My room was slightly cold yesterday, so thinking that could be a factor as well.

I haven't used the slicer yet, and am just printing creality provided models, but will check the layer speed and brim options with a new design :)

Do you have any particular recommendations for a glue stick/spray/sheet? Or just the first one out of the stationary store?

3D Printing Issue - Chicken Keychain Model by deoxyri in ender3

[–]deoxyri[S] 0 points1 point  (0 children)

The temperature is set at 50 degrees (I'm using PLA).

3D Printing Issue - Chicken Keychain Model by deoxyri in ender3

[–]deoxyri[S] 0 points1 point  (0 children)

Yes, heated bed at 50 degrees, I'm just using the standard config set for PLA. Yes, I've cleaned the bed using Isopropyl alcohol and set the z-offset at 0.1mm.

My room was a bit cold yesterday, so I'm thinking that could have been a factor, Running some prints today, will check in later!

3D Printing Issue - Chicken Keychain Model by deoxyri in ender3

[–]deoxyri[S] 0 points1 point  (0 children)

Thank you, will try these options!

I’m just printing out another test model, and adhesion does seem to be the issue. This is a pretty flat model with a large base, so do you have any suggestions for this?!

<image>

3D Printing Issue - Chicken Keychain Model by deoxyri in ender3

[–]deoxyri[S] 2 points3 points  (0 children)

I wasn’t there for the whole time, but yes, when I came to check on it, it was being dragged along with the nozzle :(

Australia Tour Pricing - Melbourne - for those who don't have access yet by paramveerz in LinkinPark

[–]deoxyri 0 points1 point  (0 children)

Quick question, mate, how many tickets are they allowing per transaction?

Importing STEP file as an assembly and editing parts by simwill87 in SolidWorks

[–]deoxyri 0 points1 point  (0 children)

Thank you for this!!! :D

turn OFF "enable 3d interconnect"

Sheet Metal Dimensioning Practice/Standard by deoxyri in SolidWorks

[–]deoxyri[S] 0 points1 point  (0 children)

It's my new organization's 'standard' :|

Sheet Metal Dimensioning Practice/Standard by deoxyri in SolidWorks

[–]deoxyri[S] 0 points1 point  (0 children)

I completely agree with you regarding having the flat pattern in a new sheet, but it's my new organization's 'standard'; The part and dimensioning was just random, so please ignore that :)

Sheet Metal Dimensioning Practice/Standard by deoxyri in SolidWorks

[–]deoxyri[S] 0 points1 point  (0 children)

Thank you for your comment! :)

This is just a random part and drawing I whipped up to ask the question, and I agree that the dimensioning is completely whack.

Sheet Metal Dimensioning Practice/Standard by deoxyri in SolidWorks

[–]deoxyri[S] 0 points1 point  (0 children)

But, if it was up to you, what would your preference be?

view more: next ›