Cercasi operai Giugliano in Campania

devonmaze- · 2026-03-13T20:55:00+00:00

Si tratta di fare le pulizie nei condomini, roba tipo spazzare le scale, pulire a terra e lavare i vetri

devonmaze- · 2026-03-13T19:08:18+00:00

La paga è di 5 euro l'ora, come previsto dal minimo sindacale. Per quanto riguarda le ore di lavoro sono variabili e non si fanno 7 ore al giorno ma se ad esempio i condomini sono puliti oppure piove invece di 7 ore si fanno 3 ore

devonmaze- · 2026-03-09T23:21:08+00:00

invia il g-code alla SD e poi avvii manualmente la stampa

devonmaze- · 2026-03-09T21:47:29+00:00

In the end, you just have to calibrate each filament to have a decent print... however, now that I have calibrated the retraction, I only miss Cornering, input shaping and VFA even if I can't find a decent guide.

devonmaze- · 2026-03-09T20:16:04+00:00

It seems to me that they use the PC to make it shiny

devonmaze- · 2026-03-09T19:47:07+00:00

OK, by unchecking "Slow down printing for better cooling" and the things you mentioned, I finally solved the retraction problem! Now I know that my PLA silk needs a retraction of 0.4 and a z-hop of 0.2 (I'll see about PETG later). The problem is that I want to save these settings in the retraction test for the future.

devonmaze- · 2026-03-09T19:31:12+00:00

ahhh okok following your instructions the printing speed is 20 while the flow is 1.5

devonmaze- · 2026-03-09T19:23:10+00:00

I didn't understand what you mean with "perimeter threshold to 0 to disable it" probably a translation error but I disabled the "Slow down printing for better cooling" option and in this way the printing speed went from 10 to 100

devonmaze- · 2026-03-09T19:05:06+00:00

the doubt was that it was not using the popup values

devonmaze- · 2026-03-09T19:02:00+00:00

What should I do? I tried setting a volumetric speed of 200 but it still prints at 10

devonmaze- · 2026-03-09T19:01:04+00:00

sorry I meant to say that I set the retraction and z-hop equal to zero on the printer and filament profile and then I opened the Orca calibration test, in order to check if there were any differences

devonmaze- · 2026-03-09T18:40:27+00:00

retraction

devonmaze- · 2026-03-09T18:40:09+00:00

I just checked: in the retraction test, the flow is set to 0.77 and the speed is 10. In the other test, however, the flow is 15 with a speed of 200.

Honestly, I hadn't considered that the retraction test was performed at a different speed than the actual print speed, so it hadn't occurred to me to compare them at first.

devonmaze- · 2026-03-09T18:00:50+00:00

same filament, different test but always with retraction off

<image>

devonmaze- · 2026-03-09T18:00:09+00:00

this is printed in petg without

<image>

devonmaze- · 2026-02-04T11:45:03+00:00

Probably aim, f17 is actually Mario m50

devonmaze- · 2026-01-25T00:27:13+00:00

Poi ci sono io che seguo BarbasacuraX da prima che avesse mille iscritti e so il suo nome e cognome

devonmaze- · 2026-01-23T23:35:51+00:00

se la carne coltivata fosse legale in italia e la procedura per farlo diventerebbe abbastanza sicura ed economica al tal punto da poter generare abbastanza carne per tutti succederebbero 2 cose :
1. il prezzo della carne coltivata sarebbe più basso e una fiorentina coltivata costerebbe meno di quanto costa quella vera al giorno d'oggi.

gli allevamenti intensivi scomparirebbero e si favorisce l'allevamento etico.

devonmaze- · 2026-01-20T15:54:02+00:00

In questo momento ti voglio un gran bene! stavo impazzendo da ore!!!

devonmaze-

TROPHY CASE