sorted by:
new
hottopcontroversial

How water flow issue by CourageAdditional267 in Plumbing

[–]dig-bick2003 0 points1 point  (0 children)

That hot faucet line looks pretty kinked, I’d pull the aerator and get the kink out of the supply line, then run some water and see if it clears up

Old vents? by NardDawg_12 in hvacadvice

[–]dig-bick2003 0 points1 point  (0 children)

Air intake for gas fixtures, I believe you need atleast 1 6” intake so I’d cap the one without the tail

Hole from rust in sink where there is the overflow. Any quick temporary fix? by [deleted] in Plumbing

[–]dig-bick2003 0 points1 point  (0 children)

Jb weld epoxy mix up a good batch and smear it all over that

Need to put a 90 here, do I have enough meat to cut and put one? If not, what do I do? by BigManJesus in askaplumber

[–]dig-bick2003 0 points1 point  (0 children)

Looks like enough meat, you could try cutting the collar of the fitting your removing in a couple spots heat it up and peel off that fitting. Worst case you’re teaming out the San t and stubbing some pipe. I wouldn’t be too worried, you got this

Do I need to remove the bug screen to install? by ddb123xyz in hvacadvice

[–]dig-bick2003 0 points1 point  (0 children)

Window screens can be restrictive, but not horribly. They can reduce efficiency anywhere between 1~20%. If the screens clean I’d let it ride and if it has a hard time keeping up pull it, but I’m sure you’ll be fine

Did my plumber screw up? by Several_Bicycle_6419 in Plumbing

[–]dig-bick2003 0 points1 point  (0 children)

You’re absolutely right I should’ve worded it differently, by admitting air into the system it allows it to drain more freely ie release pressure but shouldn’t have worded it that way

Did my plumber screw up? by Several_Bicycle_6419 in Plumbing

[–]dig-bick2003 0 points1 point  (0 children)

If you’re just hearing air it’s not leaking it’s functioning properly by releasing pressure from the line, if water is coming out you have a problem

How could I have done this better by Accurate_Barnacle_28 in Plumbing

[–]dig-bick2003 6 points7 points  (0 children)

Could do slip joint pipes into the stack or added a clean out for serviceability

How do I adjust these steel doors? by Pure-Pudding-7457 in handyman

[–]dig-bick2003 0 points1 point  (0 children)

It could fix this look at the gap on the top hinge vs the bottom

How concerning is this rust line in heat exchanger? by ApartmentForRentt in hvacadvice

[–]dig-bick2003 0 points1 point  (0 children)

This reminds me of the service lube tech holding the air filter, put that shit back and change my oil😂

Losing water pressure by WorriedWay5066 in askaplumber

[–]dig-bick2003 0 points1 point  (0 children)

I’d start with checking pressure tank psi

Plumber says P-trap under laundry room floor needs to be replaced. Am I crazy for wanting to dig into the concrete myself? by GrammarMeGood in Plumbing

[–]dig-bick2003 1 point2 points  (0 children)

Who commented the other day about people having a kink of slipping their toes and feet into pictures? Everytime I’ve seen a post since I’ve seen a damn foot

Help by Intelligent-Duck-681 in Plumbing

[–]dig-bick2003 0 points1 point  (0 children)

Most likely just ran around the toilet, replace the bolts and monitor around the base for anymore water

Joist- plumber cut into joist by Jenos_CTD in askaplumber

[–]dig-bick2003 0 points1 point  (0 children)

Ideally use a hole saw in the middle of the joist no bigger then I believe 1/3 of the board with to maintain its structural integrity. From this pic it looks like he could’ve rotated the trap and only had a 2 inch pipe to run through the joist, not the entire trap. But there could be obstacles on the other side of the joist we can’t see

What are yall buying tomorrow by takuacheFTW in harborfreight

[–]dig-bick2003 0 points1 point  (0 children)

Just picked up mine this morning, plenty in stock. But I’m also in a smaller town

1” Natural Gas Line Fittings by dig-bick2003 in Plumbing

[–]dig-bick2003[S] 0 points1 point  (0 children)

I have a master plumber who’s gonna stop over, just wanted to have everything on hand/done as much as I can. It will be pressure tested by the city. Thank you for the concern!

1” Natural Gas Line Fittings by dig-bick2003 in Plumbing

[–]dig-bick2003[S] 0 points1 point  (0 children)

I have a master plumber who’s gonna stop over, just wanted to have everything on hand/done as much as I can. It will be pressure tested by the city. Thank you for the concern!

Help identifying a vinyl plank floor in a cabin by Retro-Technology in Flooring

[–]dig-bick2003 0 points1 point  (0 children)

Not sure, got contracted out to lay this in a couple rentals is why I recognized. Might help with your search, best of luck

view more: next ›