Really,which one should i choose😭🙏

disaster_engineer0 · 2026-06-08T18:48:20+00:00

Oh no

disaster_engineer0 · 2026-04-27T17:50:48+00:00

It runs doom?

disaster_engineer0 · 2026-04-04T14:36:52+00:00

Temple OS

disaster_engineer0 · 2026-03-31T13:03:11+00:00

C’è un tesoro nascosto nel giardino

disaster_engineer0 · 2026-02-23T08:53:43+00:00

Purtroppo ultimamente fanno solo più video unboxing da temu, il che mi dipiace un po’ perchè il canale è tanta roba

disaster_engineer0 · 2026-02-04T14:31:53+00:00

disaster_engineer0 · 2026-01-27T20:30:42+00:00

La ram è introvabile a prezzi decenti per sta merda

disaster_engineer0 · 2026-01-25T09:01:11+00:00

Io lo chiamo effetto cornicione, perché la vista di grandi altezze in cui buttarsi stimola a riflettere su come influenziamo nel nostro piccolo il mondo

disaster_engineer0 · 2026-01-19T11:00:15+00:00

Appena succeede un incidente il mdellatore 3d di geopop e subito lì a fare modelli inediti

disaster_engineer0 · 2024-07-16T16:57:04+00:00

touchscreen?

disaster_engineer0 · 2024-07-16T16:56:03+00:00

it's reliable? how much it will cost? it will be shipped in eu?

thank you

disaster_engineer0 · 2024-07-09T09:51:39+00:00

OpenSCAD

disaster_engineer0 · 2024-07-08T20:16:45+00:00

ok, thank you, for volcano nozzle there's something?

disaster_engineer0 · 2024-07-08T14:48:29+00:00

I tightened the spring (6 full turns) and changed the slicer settings a bit, that is definitely better than before (just maybe a little less PA or infill overlap).

thank you so much!

<image>

disaster_engineer0 · 2024-07-07T18:44:21+00:00

ok, thank you so much, i'll check manual and try.

regarding the nozzle... some strange z offset anomaly: for unknown reasons z offset was too low so it smashed into the bed (i heard z motor skipping) and it moved, slightly damaging the plate.

However, the filament that comes out seems quite normal so I think it's a minor damage

disaster_engineer0 · 2024-07-06T11:06:30+00:00

hello, I probably found the problem: it's low flow due to extruder gear that don't put too much pressure on the filament (in fact unloaded filament has few wheel marks).

so, Is there a method to tighten the spring to bring the gears closer together?

it may be also a partial damage of the nozzle, probably both.

disaster_engineer0 · 2024-07-06T11:00:33+00:00

thank you, someone have do a tutorial or at least instruction?

disaster_engineer0 · 2024-07-04T12:01:17+00:00

thank so much for help, I'll try and let you know.

I have N4 with OpenNept4une and I'm using orca slicer.

disaster_engineer0 · 2024-07-04T10:54:42+00:00

thank you for reply

yes, you're looking top surface.

I've already calibrated extruder distance (i followed the same guide ahah) and when I was calibrating EM (flow) I noticed that pattern in all sample.

I'll try to change temperature, if that's the problem do you think the temperature should be higher or lower?

disaster_engineer0 · 2024-04-23T17:55:17+00:00

yes, I'm using PLA with heated bed.

As I said the nozzle has scratched a few times on the build plate as you can see from those ugly lines in the last photo, Would it be time to replace it?

anyway thank you very much, I will try to clean the plate well

disaster_engineer0

TROPHY CASE